Recording A Cd: Specifying Track Order (Programme Edit) - Sony CHC-P33D Mode D'emploi

continued
4
Press + or = on the remote to
designate the tape length.
Choose the indication for tapes of a
corresponding minute length. Choose
"HALF" if you want the CD player to
play just half the total playing time of
the CD.
As you press the button, the indication
changes as follows:
C-46
(23.00)
C-90 C-74
(45.00) (37.00)
Note
You cannot select "HALF" when you
want to record CD with more than 20
tracks.
5
Press EDIT.
EN
The CD player determines the tracks to
be recorded on side A automatically.
14
Total playing time on side A
6
When you want to record on both sides,
press EDIT again.
The CD player determines the tracks to
be recorded on side B.
When you want to record only on side
A, press p to stop the indication from
flashing.
7
Press § EJECT DECK B and insert a
blank tape into deck B with the side you
want to record on facing forward.
Recording will start from the front side
of the tape, unless you have changed the
playing direction before recording.
Make sure the tabs on the cassette have
not been removed.
8
Select dual or single-sided recording.
To record
One side
Both sides*
* Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
9
Press CD SYNCHRO.
Deck B stands by for recording.
Chapter 4: the Tape Player
10
Recording starts.
After about 10 seconds, the CD starts
playing.
To stop recording
Press p.
To cancel time edit
Press PLAY MODE.
To select the desired tracks
C-54
beforehand
(27.00)
You can place priority on some tracks to be
C-60
recorded by selecting them before
(30.00)
programming (only up to 20 tracks). See
"Playing Tracks in the Desired Order
(programme play)".
To activate DOLBY NR
When you want to reduce the hiss noise in
low-level high-frequency signals, press
DOLBY NR so that "DOLBY NR B" appears
in the display after step 8.
Recording a CD:
Specifying Track
Order (programme
edit)
You can adjust the total recording time to
the tape length while making a programme.
3
7,12
1
Press CD.
2
Press § OPEN/CLOSE CD and place a
Press DIRECTION
CD. Then, press § OPEN/CLOSE CD
MODE to select
again to close the disc tray.
A
3
ß or RELAY
Press PLAY MODE repeatedly until
"PROGRAM" appears in the display.
4
Turn the jog dial to choose a track.
5
Press ENTER/NEXT.
6
Repeat steps 4 and 5 to programme the
remaining tracks you want to record on
side A in the order you want them to be
recorded.
Press P to release recording pause.
p
7
Press P to pause recording at the end of
side A. The total playing time "0.00" is
displayed.
8
Repeat steps 4 and 5 to programme the
remaining tracks you want to record on
side B in the order you want them to be
recorded.
9
Press § EJECT DECK B and insert a
blank tape into deck B with the side you
want to record on facing forward.
Recording will start from the front side
of the tape, unless you have changed the
playing direction before recording.
Make sure the tabs on the cassette have
not been removed.
10
Select dual or single-sided recording.
To record
One side
Both sides*
* Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
11
Press CD SYNCHRO.
Deck B stands by for recording.
12
Press P to release recording pause.
Recording starts.
After about 10 seconds, the CD starts
playing.
To stop recording
Press p.
To cancel programme edit
Press PLAY MODE.
11
10
To activate DOLBY NR
9
When you want to reduce the hiss noise in
2
low-level high-frequency signals, press
DOLBY NR so that "DOLBY NR B" appears
5
in the display after step 10.
4
1
Press DIRECTION
MODE to select
A
ß or RELAY