Recording A Cd: Specifying Track Order (Programme Edit) - Sony MHC-W55 Mode D'emploi

3
Press EDIT twice.
"TAPE SELECT" then "TIME EDIT"
appear in the display.
4
Turn the JOG dial (or press = or +
on the remote) to choose the indication
that corresponds to the length (in
minutes) of your tape.
The indications change as follows:
HALF C-46 C-54
(23.00) (27.00)
C-90 C-74 C-60
(45.00) (37.00) (30.00)
CD
1 2 3 4 5
6 7 8 9 10
DOLBY NR B OFF
11
63 125 250 500 1k 2k 4k 8k 16k(Hz)
DISC PROGRAM
Choose "HALF" if you want the CD
player to half of the total playing time of
the CD. You cannot select "HALF"
when recording CDs with more than 20
tracks.
5
Press EDIT.
The CD player determines the tracks to
be recorded on side A automatically.
Tracks to be recorded on side A
CD
1 2 3 5
6
DOLBY NR B OFF
63 125 250 500 1k 2k 4k 8k 16k(Hz)
DISC PROGRAM
Total playing time on side A
6
To record on both sides, press EDIT
again. The CD player determines the
tracks to be recorded on side B.
If you only want to record on side A,
press p on the CD player to stop the
flashing in the display.
7
Press § EJECT and insert a blank tape
into deck B with the side you want to
record on facing forward.
Recording starts from the front side of
the tape, unless you change the playing
direction before recording.
Make sure the tabs on the cassette have
not been removed.
8
Select dual or single-sided recording.
To record Press DIRECTION
MODE to select
One side of the tape A
Both sides* ß or RELAY
* Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
9
Press CD SYNCHRO.
Deck B stands by for recording.
10
Press P PAUSE to release recording
pause.
Recording starts.
After about 10 seconds, the CD starts
playing.
To stop recording
Press p on the tape player or the CD
player.
To check the order
Press CHECK on the remote repeatedly.
Each time you press CHECK, the number
of the programmed tracks appear in the
display.
To cancel time edit
A VOLUME
Press p on the CD player, then press PLAY
DBFB
MODE.
To select the desired tracks
beforehand
You can record certain tracks (up to 20) first
by selecting them before time editing. See
"Playing Tracks in the Desired Order
(programme play)".
To activate DOLBY NR
When you want to reduce the hiss noise in
low-level high-frequency signals, press
DOLBY NR so that "DOLBY NR B" appears
in the display after step 8.
A VOLUME
DBFB
Recording a CD:
Specifying Track
Order (programme
edit)
You can adjust the total recording time to
the tape length while making a programme.
SYSTEM
POWER m ON
5
3
⁄
p
Æ
»
p
0 )
r P
⁄
11 12
DOLBY NR
=/+
1
Press FUNCTION repeatedly until "CD"
appears in the display.
2
Press § OPEN/CLOSE/EX-CHANGE
and place a CD.
Then, press § OPEN/CLOSE/
EX-CHANGE again to close the CD tray.
If the button for the disc tray containing
the CD you want to record is not lit
green, press DISC SKIP repeatedly so
that it lights green.
3
Press PLAY MODE repeatedly until
"PROGRAM" appears in the display.
4
Turn the JOG dial (or press = or +
on the remote) to choose a track.
continue to next page
Chapter 4: the Tape Player
1
4
p
» P
2
»
Æ
p
p
0 )
GB
⁄
17
9 10
7