Télécharger Imprimer la page

EINHELL BT-CS 1200/1 Mode D'emploi D'origine page 13

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
Anleitung_BT_CS_1200_SPK1:_
Blade holder:
Blade thickness:
Protection class:
Weight:
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L
sound pressure level
93,9 dB(A)
pA
K
uncertainty
pA
L
sound power level
104,9 dB(A)
WA
K
uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 60745.
Handle
2
Vibration emission value a h = 2.924 m/s
2
K uncertainty = 1.5 m/s
Additional handle
2
Vibration emission value a h ≤ 2.965 m/s
2
K uncertainty = 1.5 m/s
Additional information for electric power tools
Warning!
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment
is used and may exceed the specified value in
exceptional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
10.01.2011
9:02 Uhr
Ø 16 mm
Have the appliance serviced whenever
necessary.
2.5 mm
Switch the appliance off when it is not in use.
II / ®
Wear protective gloves.
3.8 kg
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.
3 dB
3. Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
3 dB
is not properly guided and maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1 Setting the cutting depth (Figure 2/3)
Release the handle on the rear of the guard hood
for adjusting the cutting depth (4).
Place the saw foot (6) flat on the surface of the
workpiece you wish to saw. Raise the saw until
the saw blade (12) is at the required cutting depth
(a).
Refasten the handle for adjusting the cutting
depth (4). Check the handle is securely fastened.
5.2 Miter stop (Figure 4/5)
The preset standard angle between the saw foot
(6) and saw blade (12) is 90°. You can adjust this
angle to carry out angled cuts.
Release the locking lever for miter setting (7) on
the front of the saw foot.
You can now adjust the cutting angle to around
45°. Keep an eye on the cutting angle scale (9) as
you do so.
Refasten the locking lever for miter setting (7).
Check the handle is securely fastened.
5.3 Extraction of dust and chips (Figure 6)
Connect a suitable vacuum cleaner (a) to the
provided chip extractor connector (14) of your
circular saw (vacuum cleaner not included). This
will provide excellent dust extraction on the
Seite 13
GB
13

Publicité

loading

Ce manuel est également adapté pour:

43.309.32