SCHOLTES CI 66 V W S Mode D'emploi page 22

Masquer les pouces Voir aussi pour CI 66 V W S:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

• Secure the power supply cable by fastening the
cable clamp screw then put the cover back on.
GB
Connecting the supply cable to the electricity mains
Install a standardised plug corresponding to the load
indicated on the appliance data plate (see Technical
data table).
The appliance must be directly connected to the mains
using an omnipolar switch with a minimum contact
opening of 3 mm installed between the appliance and
the mains. The switch must be suitable for the charge
indicated and must comply with current electrical
regulations (the earthing wire must not be interrupted
by the switch). The supply cable must be positioned
so that it does not come into contact with temperatures
higher than 50°C at any point.
Before connecting the appliance to the power supply,
make sure that:
• The appliance is earthed and the plug is compliant with
the law.
• The socket can withstand the maximum power of the
appliance, which is indicated by the data plate.
• The voltage falls between the values indicated on
the data plate.
• The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only.
! The manufacturer declines any liability should
these safety measures not be observed.
Safety Chain
The cooker is fitted with a safety chain to be fixed by
means of a screw (not supplied with the cooker) to
the wall behind the appliance, at the same height as
the chain is attached to the appliance.
22
Choose the screw and the screw anchor according
to the type of material of the wall behind the applian-
ce. If the head of the screw has a diameter smaller
than 9mm, a washer should be used. Concrete wall
requires the screw of at least 8mm of diameter, and
60mm of length.
Ensure that the chain is fixed to the rear wall of the
cooker and to the wall, as shown in figure, so that
after installation it is tensioned and parallel to the
ground level.
TABLE OF CHARACTERISTICS
Oven dimensions
(HxWxD)
Volume
Useful
measurements
relating to the oven
compartment
Burners
Voltage and
frequency
Glass Ceramic Hob
Front Left
Back Left
Back Right
Front Right
Max. Ceramic Hob
Consumption
! In order
ENERGY LABEL
to prevent
and ECODESIGN
accidental
tipping of the
appliance, for
example by
a child clim-
bing onto the
oven door, the
supplied safety
chain MUST be
installed!
Data plate, is located inside the flap or, after the oven
compartment has been opened, on the left-hand wall
inside the oven.
32,4x43.5x40,3 cm
57 l
width 42 cm
depth 44 cm
height 8.5 cm
may be adapted for use with any type
of gas shown on the data plate
see data plate
1700W
1200W
2300W
1200W
6400W
Regulation (EU) No 65/2014 supplemen-
Regulation (EU) No 65/2014 supplemen-
ting Directive 2010/30/EU.
ting Directive 2010/30/EU.
Regulation (EU) No 66/2014 implementing
Regulation (EU) No 66/2014 implementing
Directive 2009/125/EC.
Directive 2009/125/EC.
Standard EN 60350-1
Standard EN 60350-1
Standard EN 50564.
Standard EN 50564.
Standard EN 30-2-1
Energy consumption for Natural
convection – heating mode:
Convection mode
Declared energy consumption for
Forced convection Class
– heating mode: Roasting
EC Directives: 2006/95/EC dated
12.12.06 (Low Voltage) and
subsequent amendments - 04/108/EC
dated 15/12/04 (Electromagnetic
Compatibility) and subsequent
amendments - 93/68/EEC dated
22/07/93 and subsequent
amendments - 2002/96/EC.
1275/2008 (Stand-by/Off mode)

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Ci 66 v i sCi 66 v a sCi 66 v w s 0Ci 66 v i s 0Ci 66 v a s 0

Table des Matières