Operation; Electrical Connection - Scheppach HCE1600 Mode D'emploi

Connect the accessory's hose to the high-pressure
cleaner, and make sure that the suction strainer re-
mains under water.
Let the high-pressure cleaner run with the spray gun
removed until the water flows evenly out of the high-
pressure hose.
If no water comes out after 25 to 50 seconds, switch
off and check all connections.
Once the water is flowing, turn off the high-pressure
cleaner and connect the spray gun and spray lance
to start work.
High-pressure hose connection (Fig. 3/4)
Connect the high-pressure hose (9) to the connec-
tion for the high-pressure hose (4). Remove the pro-
tective cover first.
Insert the other end of the high-pressure hose (9)
into the pistol connection (8).
To remove the high-pressure hose (9), press the but-
ton (A) and pull it out.
Connecting the attachments (Fig. 5)
To mount attachments 7, 9, 11, 12, 16, 17 press them
into the pistol (8) and turn them until the lock.
To mount attachments 10, 13, 18 insert these into the
attachment (7) and turn them until they lock.

8. Operation

The equipment consists of an assembly with a pump,
which is encased in a shock absorbing housing. The
equipment comes with a lance and a non-slip gun (for
an optimal working position), whose shape and con-
figuration comply with the applicable regulations.
Commissioning:
Once you have completely assembled the high-pres-
sure cleaner and all connections have been made,
proceed as follows:
Turn on the water supply. Unlock the pistol (8) via
the locking switch (C). Pull back the trigger lever (D)
so that the air in the device can discharge. (Fig. 5)
Switch on the device by setting the on/off switch (3)
to "ON". Next, press the trigger lever (D). (Fig. 1/5)
To switch off, release the trigger lever (D), and the
device switches to stand-by. The high-pressure
cleaner starts again when you press the trigger le-
ver (D). (Fig. 5)
To switch off the high-pressure cleaner completely,
set the on/off switch (3) to "OFF". (Fig. 1)
Cleaner container (11)
Fill the cleaner container with the corresponding
cleaner. The beam width can be adjusted at the noz-
zle.
20 І GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Using the attachments (Fig. 1):
R-Nozzle (10): For coarse cleaning work.
Kärcher-adapter (12): Use this adapter to attach
Kärcher brand accessories.
Terrace cleaner (13): For cleaning floor and wall sur-
faces.
Rotating brush (17): For surface cleaning
Cleaning brush (16): For surface cleaning.
H-nozzle (18): For eliminating stubborn dirt.
9. Electrical connections
The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions.
The customer's mains connection as well as
the extension cable used must also comply with
these regulations.
Damaged electrical connection cable
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insula-
tion damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking „H05VV-F".
The printing of the type designation on the connec-
tion cable is mandatory.
AC motor
• The mains voltage must be 230 V~
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm .
2
Connections and repairs of electrical equipment may
only be carried out by an electrician.