Introduction; Device Description - Scheppach HCE1600 Mode D'emploi

1. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
Repairs by third parties, not by authorized service
•
technicians,
Installation and replacement of non-original spare
•
parts,
Application other than specified,
•
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
WE RECOMMEND:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture.
Read the instruction manual each time before op-
erating the machine and carefully follow its informa-
tion. The machine can only be operated by persons
who were instructed concerning the operation of the
machine and who are informed about the associ-
ated dangers. The minimum age requirement must
be complied with. In addition to the safety require-
ments in these operating instructions and your coun-
try's applicable regulations, you should observe the
generally recognized technical rules concerning the
operation of machines.
16 І GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
We accept no liability for accidents or damage that
occur due to a failure to observe this manual and the
safety instructions.
2. Device Description (Fig.1)
1. Handle
2. Lance holder
3. On/off switch
4. High-pressure hose connection
5. Transport wheel
6. Hose holder
7. Extension
8. Pistol
9. High-pressure hose
10. R-Nozzle
11. Cleaner container
12. Kärcher adapter
13. Patio cleaner
14. Water supply connection
15. Nozzle cleaning needle
16. Cleaning brush
17. Rotating brush
18. H-Nozzle
3. Unpacking
Open the packaging and remove the device care-
•
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
Check that the delivery is complete.
•
Check the device and accessory parts for trans-
•
port damage.
If possible, store the packaging until the warranty
•
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
4. Proper use
The high-pressure cleaner is designed to clean ve-
hicles, machines, buildings, facades, etc. in the pri-
vate sector.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufac-
turer will be liable for any damage or injuries of any
kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial ap-
plications.