Technical Data; Before Starting The Equipment; Operation - EINHELL TE-VC 18/10 Li Traduction Du Mode D'emploi D'origine

Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............................18 V
Air fl ow: ............................. 42.4 cfm (1.2 m³/min)
Sealed suction: ...........................1.2 psig (8 kPa)
Vacuum hose length: ... 2.2 to 6.6 ft (0.7 m to 2 m)
Tank capacity: ...............................2.65 gal (10 l )
Weight (Tool only): ........................... 6.6 lbs (3 kg)

5. Before starting the equipment

5.1 Assembling the equipment
Fitting the head (Fig. 4)
The equipment head (3) is fastened to the
tank (7) by the locking hook (6). To remove the
equipment head (3), open the locking hook (6)
and take off the equipment head (3). When fi tting
the equipment head (3), make sure that the
locking hook (6) locks into place correctly.
5.2 Fitting the fi lters
Important!
Never use the wet/dry vacuum without a fi lter.
Always ensure that the fi lters are securely seated.
Fitting the foam fi lter (Fig. 5/Item 14)
For wet-vacuuming, slip the supplied foamed
plastic fi lter (14) over the fi lter basket (Figs. 3/4).
Fitting the additional fi lter (Fig. 6)
For dry vacuum cleaning always use the supplied
additional fi lter (16). Fit the additional fi lter, so that
no air is sucked through the fi lter cage (4) without
being fi ltered.
Fitting the dirt bag (Fig. 7/Item 15)
For vacuuming fi ne, dry dirt it is recommended
that you fi t the dirt bag (Fig. 7/Item 15). Slip the
dirt bag (15) over the vacuuming hole. The dirt
bag (54) is suitable for dry-vacuuming only. The
dirt bag makes it easier to dispose of the sucked-
in dust.
Anl_TE_VC_18_10_Li_USA_SPK7.indb 9 Anl_TE_VC_18_10_Li_USA_SPK7.indb 9
EN
5.3 Fitting the suction hose (Fig. 1, 3)
Connect the suction hose (10) to the
corresponding connector on the wet/dry vacuum,
depending on the application required.
Vacuuming
Connect the suction hose (10) to the suction hose
connector (8).
Blowing
Connect the suction hose (10) to the blow
connector (9).
5.4 Suction nozzles
Crevice/brush nozzle (Fig. 2)
The crevice/brush nozzle with swing-out brush
(12) is designed for vacuuming solids and liquids
in corners, edges and other areas that are diffi cult
to access.
Upholstery/universal nozzle (Fig. 2)
Fitted with the brush insert (13), the nozzle is
designed for vacuuming solids from upholstery
and carpets. Without the brush insert (13) fi tted,
the nozzle is designed for vacuuming solids and
liquids from small to medium-sized surfaces. To
remove the brush insert, press the button and
pull the brush insert off to the side at the same
time.
Fitting the tool adapter
You can use the supplied tool adapter (Fig. 2/
Item 19) to connect the suction hose (10) to the
tool. To do so, fi t it between the suction hose
and the extractor port on the tool. Check that the
connections are secure and air-tight.
Fitting the battery (Fig. 8)
Open the battery cover (15). To do so, fl ip
the cover up as shown in Fig. 8. Then slot the
rechargeable battery (18) into the mount and
push it forward until you hear the battery engage.

6. Operation

6.1 On/Off switch (Fig. 1/Item 2)
Switch position 0: Off
Switch position I: On
6.2 Dry vacuuming
Use the additional fi lter (16) for dry vacuuming
(see point 5.2). Always ensure that the fi lters are
securely seated.
- 9 -
19.03.2020 10:55:07 19.03.2020 10:55:07