Ravelli Vittoria V Déco Manuel D'utilisation Et D'entretien page 154

To exit the page and return to Stand-by page, press the button repeatedly.
Control: ventilation can be set from 0 to AUTO where 0 indicates that the same is disabled, setting from MIN to MAX enables selecting
the heat distribution speed. If set to AUTO, the ventilation follows the power set on the stove.
Chronothermostat
With the Chrono-thermostat function you can program the automatic switch ON/OFF of the stove for each day of the week for each
Chrono function
day of the week in 4 independent time intervals (SET CHRONO 1-2-3-4). Below are given the steps for accessing the relative menu
By enabling the chrono function, it is possible to control the ventilation speed for each program as shown in the logic above.
starting from "Home" mode.
MANUFACTURER'S
TECHNICIAN
TECHNICIAN
PRODUCER
Press the key
"access menu" to
access the
MENU page
CHRONOTHERMOSTAT
CHRONO
ENABLE CHRONO
ENABLE CHRONO
SET CHRONO 1
SET CHRONO 1
SET CHRONO 2 SET CHRONO 2
SET CHRONO 3
SET CHRONO 3
SET CHRONO 4
SET CHRONO 4
CHRONOTHERMOSTAT
CHRONO
ENABLE CHRONO
ENABLE CHRONO
SET CHRONO 1
SET CHRONO 1
SET CHRONO 2
SET CHRONO 3
SET CHRONO 2
SET CHRONO 4 SET CHRONO 3
SET CHRONO 4
The exit key shows the CHRONO menu to set other variables related to the menu functions.
The exit key shows the CHRONO menu to set other variables related to the menu functions.
To exit the page and return to Stand-by page, press the button repeatedly.
To exit the page and return to "Home" page, press the button repeatedly.
Set air - pellet
Pages displayed upon the activation of advanced layouts
The setting of the PELLET-FLOW mixture allows to adjust the combustion by varying the quantity of pellets loaded in the brazier
By activating a layout different from the standard (layout 0), even if maintaining the same functions of the menu, the "Stand-by" page will
and/or the quantity of air. In fact, by its nature, pellets vary in grain size and composition: even bags of pellets of the same brand
display all connected utilities such as the temperature of the boiler of the puffer.
can have different characteristics.
Below is shown the new display mode and the function of every icon for every layout, to change the various settings.
If combustion is not optimal, vary the flow parameter to adjust the combustion air. If air regulation alone is not sufficient, it may also
⚠
be necessary to modify the pellet parameter.
If the type of system designed requires controlling the 3-way valve (diagram 1 and 3), it is necessary to purchase the
optional kit from the retailer or the authorized Ravelli dealer.
Stove State Combustion regulation is an operation that requires a lot of experience. We recommend that you contact an Authorised
Service Centre to calibrate the stove appropriately.
Below are given the steps for accessing the relative menu starting from Stand-By mode.
Layout 1 (DHW Boiler + heating control)
The following layout can be used when you have a boiler that is not equipped with plate heat exchanger and you intend to buy a puffer
MENU
MENU
that should be connected to the circuit to produce hot domestic water.
In this type of circuit, room temperature is controlled however by the handheld unit which, being a radio device, acts as a remote
USER
chronothermostat. The boiler is managed by the thermostove through a contact or immersion probe (not supplied) connected directly
MANUFACTURER'S
to the back of the stove. Below is shown the new "Stand-by" mode.
TECHNICIAN
TECHNICIAN
PRODUCER
Press the key
"access menu" to
access the
MENU page
STOVE STATE
ACTIVE PARTS
ACTUAL STATES
STATE TEMPERATURE
H20 TEMPERATURE
Use the UP and DOWN
keys to change the % pellet
value.
The operation is the same as for the basic layout except for the fact that in this layout, the boiler exchanges heat directly in the
boiler (priority); when the temperature set is reached, the 3-way valve changes its position and the boiler starts exchanging heat within
the heating circuit. From this moment, the stove is controlled by the radio handheld unit for contolling the room
To exit the screen and return to the home screen, press the key repeatedly.
temperature or via H2 setting (see the operation with layout 0 to find the data on modulation, eco stop etc.).
The 3-way valve is directed again into the boiler when:
- there is a request from the Boiler;
PUMP
- there is a requested from the flow switch (optional, if connected).
3-WAY VALVE HEAT
Use and maintenance manual Vittoria Déco
MENU
MENU
USER
USER
Manuale utente PALMARE IDRO TOUCH RADIO
Press the key
"confirm"
to access the
USER page
Manuale utente PALMARE IDRO TOUCH RADIO
Stove State
Below are given the steps for accessing the relative menu starting from Stand-By mode.
USER
T°C Boiler
From STAND BY mode, press
the ARROW key UP
Press the key
Press the key
to set the
"access menu" to "confirm"
room T°C
access the to access the
and DHW boiler T°C that you
MENU page USER page
desire.
Boiler water T°C
From STAND BY mode, press
STOVE STATE
STOVE STATE
the ARROW key DOWN
ACTIVE PARTS
ACTIVE PARTS
% Flow
the boiler water T°C
ACTUAL STATES
ACTUAL STATES
that you desire.
STATE TEMPERATURE
STATE TEMPERATURE
H20 TEMPERATURE
H20 TEMPERATURE
Press the CONFIRM button
to confirm the value and
go to the item % change
flow.
POWER MOD PUMP
3-WAY VALVE HEAT
USER
USER
POWER SETTING
LOADING AUGER
CHRONOTHERMOSTAT
CHRONOTHERMOSTAT
SCREW LOADING
SET AIR-PELLET
SET AIR-PELLET
STOVE STATUS
ENABLE CHRONO
1 2
3
4
"enter" at the end of the
5 6
setting, from the following
CHRONO page
Manuale utente PALMARE IDRO TOUCH RADIO
USER
MENU
USER
POWER SETTING
USER
LOADING AUGER
CHRONOTHERMOSTAT
MANUFACTURER'S
CHRONOTHERMOSTAT
SCREW LOADING
TECHNICIAN
SET AIR-PELLET
SET AIR-PELLET
STOVE STATUS
STOVE STATE
STOVE STATE
to set
ACTIVE PARTS
% Flow
ACTUAL STATES
STATE TEMPERATURE
STATE TEMPERATURE
H20 TEMPERATURE
Use the UP and DOWN buttons to change the
pellet % value. Press the CONFIRM button to
HH T ...
POWER MOD
EXT.T ...
FLAME T 340°C
to change the ventilation.
CHRONOTHERMOSTAT
CHRONOTHERMOSTAT
Press the key
several times
to quickly switch to
CRONO-THERMOSTAT.
ENABLE CHRONO
1
Ignition time
VENTILATION POW.
2
Shutdown time
3
Day of the week when the
program is active
4
Program number "chrono"
5
Press the key
Power setting
6
Setting the room temperatures
USER
LOADING AUGER
POWER SETTING
CHRONOTHERMOSTAT
CHRONOTHERMOSTAT
SET AIR-PELLET
SCREW LOADING
SET AIR-PELLET
STOVE STATUS
POWER MOD
Press the key Press the selection
Press the key
"confirm" keys to navigate the
PUMP
several times
to access the menu screens.
to quickly switch to
3-WAY VALVE HEAT
USER page USER.
Stove STATUS.
PRESSURE 1.1 BAR
HH T . 21°C
STOVE STATE
Press the key
ACTIVE PARTS
"V" from STAND BY page
to display the actuale states and
ACTUAL STATES
ACTUAL STATES
the room temperature
STATE TEMPERATURE
v H20 TEMPERATURE
confirm the value and
change to the item % flow.
Rev.1 10/03/2021
Pag.37
USER
USER
LOADING AUGER
POWER SETTING
SCREW LOADING
SET AIR-PELLET
STOVE STATUS SET AIR-PELLET
Vers. 01 del 07/04/15
Pag.33
Press the increase/decrease keys
"increase/decrease"
to change the ventilation.
Vers. 01 del 07/04/15
Pag.30
USER
USER
STOVE STATE
COMFROT CLIMA
SETTING
Press the key
Select SET AIR-PELLET
several times
and press the CONFIRM
to quickly switch to
button.
Stove STATUS.
STOVE STATE
ACTIVE PARTS
ACTIVE PARTS
ACTUAL STATES
STATE TEMPERATURE
v
HH T ...
EXT.T ...
FLAME T 340°C