English - Milwaukee AGVK24-230EK Notice Originale

TECHNICAL DATA
Angle Grinder
Production code
Rated input
Rated speed
D= Grinding disk diameter max.
d= Grinding disk hole diameter
b= Cutting disk thickness min. / max.
b= Grinding disk thickness max.
D= Grinding surface diameter max.
D= Wiring brush diameter max.
Thread of work spindle
Weight according EPTA-Procedure 01/2014
Noise information
Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 60745
Surface grinding: Vibration emission value a
Uncertainty K=
Disk sanding: Vibration emission value a
Uncertainty K=
For other applications, e.g. Abrasive Cutting-O Operations or Wire Brushing other vibration values could occur.
WARNING!
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for di erent applications,
with di erent accessories or poorly maintained, the vibration emission may di er. This may signi cantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is
running but not actually doing the job. This may signi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e ects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
WARNING!
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock,
re and/or serious injury.
Save all warnings and instructions for future reference.
ANGLE GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire
Brushing or Abrasive Cutting-O Operations:
a) This power tool is intended to function as a grinder,
sander, wire brush or cut-o tool. Read all safety warnings,
instructions, illustrations and speci cations provided with
this power tool. Failure to follow all instructions listed below may
result in electric shock, re and/or serious injury.
h,SG
h,DS
b) Operations such as polishing are not recommended
to be performed with this power tool. Operations for which
the power tool was not designed may create a hazard and cause
personal injury.
c) Do not use accessories which are not speci cally
designed and recommended by the tool manufacturer. Just
because the accessory can be attached to your power tool, it does
not assure safe operation.
d) The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool. Accesso-
ries running faster than their rated speed can break and y apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of your power
tool. Incorrectly sized accessories cannot be adequately guarded
or controlled.
AGVK24-230EK AGVK24-230EK DMS
4499 76 02... 4499 90 02...
... 000001-999999 ... 000001-999999
2400 W 2400 W
6600 min 6600 min
-1
230 mm 230 mm
22,2 mm 22,2 mm
1,9 / 3 mm 1,9 / 3 mm
8 mm 8 mm
230 mm 230 mm
100 mm 100 mm
M 14 M 14
5,4 kg 5,4 kg
92,5 dB (A) 94,5 dB (A)
103,5 dB (A) 105,5 dB (A)
6,1 m/s 6,5 m/s
2
1,5 m/s 1,5 m/s
2
2,2 m/s 2,7 m/s
2
1,5 m/s 1,5 m/s
2

English

-1
GB
2
2
2
2
13