Bosch PPR 250 Notice Originale page 20

OBJ_BUCH-1513-004.book Page 20 Tuesday, November 26, 2013 4:07 PM
20 | English
– Attach the double-SDS-connector 27 to adapter 31 on the
water tap.
– Hold the paint applicator 3 over a suitable collecting con-
tainer (e. g. a bucket).
– Carefully open the water tap and run lukewarm water
through the system.
– When flushing, lightly press pump hose 33 together sever-
al times.
This will lead to better cleaning results.
Additionally, this also cleans bypass hose 34, which pre-
vents the rotor from overloading in case of excessive pres-
sure in the hose system.
– Flush the system until only clear water comes out of the
paint applicator.
– Clean the paint filter 22 and the intake hose 4 (connect
SDS connection 32 to the water tap and flush; additional
cleaning of paint filter with brush).
– Release the adapter 31 from the water tap and from the
double-SDS-connector 27.
Screw the mixing nozzle back onto water tap.
Cleaning the paint applicator and the paint roll:
– See "Cleaning the Paint Applicator and the Paint Roll",
page 20.
Mounting together the dried components:
– Allow all components to dry thoroughly.
If possible, hang up the paint roll 16 to dry.
If the paint roll is placed down to dry, the pile will be de-
formed. This may lead to an uneven surface quality when
using the paint roller the next time.
– Reconnect the intake hose 4 to the SDS connection 32 on
the paint filter 22.
– Manually turn rotor 35 to the indicated position (see figure
G4) in order to avoid damage to pump hose 33 when in-
serting pump lid 20.
– Reinsert the pump lid 20 into the housing opening and
push it upward to the stop.
– Shut pump lock 23 until it engages.
– Lock holding clamp 21 again.
Alternative Cleaning Method (see figure H)
Note: This cleaning method takes somewhat longer than the
EasyClean method.
– Couple base unit 5 to the water bucket (also see "Coupling
the Base Unit and the Paint Bucket", page 17).
– Insert paint filter 22 to the bottom of the water bucket.
– Fasten the intake hose 4 in the holding clip 28.
– Plug the mains plug into a socket outlet.
– Make sure that the pump lock 23 is engaged.
– To start the machine, push the On/Off switch 18 to the "I"
position.
– Hold paint applicator 3 over a suitable collecting container
(e.g. a bucket) and actuate trigger switch 7 until only clear
water comes out of the paint applicator and no more paint
can be seen in the hoses (visual check).
Always lightly move the hoses.
This will lead to better cleaning results.
– Clean the paint applicator and the paint roll: See "Cleaning
the Paint Applicator and the Paint Roll", page 20.
2 609 006 717 | (26.11.13)
– Allow all components to dry thoroughly.
If possible, hang up the paint roll 16 to dry.
If the paint roll is placed down to dry, the pile will be de-
formed. This may lead to an uneven surface quality when
using the paint roller the next time.
Cleaning the Paint Applicator and the Paint Roll
(see figures I1 –I3)
After flushing the system, some of the components still have
to be cleaned manually.
– Remove paint remainders from paint applicator 3 using a
brush.
– Pull paint distributor 36 out of the paint chamber 37.
For easier cleaning, turn the paint distributor by 90°.
– Remove the distributor plate 38 from the paint distrib-
utor 36.
For this, lift the distributor plate on one side and pull it lat-
erally out of the retaining clamps.
– Remove paint remainders from of the distributor plate 38,
the paint distributor 36 and from of the paint chamber 37
using a small brush.
– Wash out the paint roll 16 thoroughly.
Storage
Before storing, the electric paint roller must be properly
cleaned and all components dried.
– Slide distributor plate 38 laterally into the retaining clamps
in paint distributor 36.
– Clip paint distributor 36 into the paint chamber 37.
– Wind up feed hose 2 around the base unit 5 and affix it with
holding clamp 21.
– Slide down paint-bucket coupling 29 completely to the
bottom.
– Insert paint roll 16 into paint applicator 3 (see "Changing
the Paint Roll", page 18).
Material Disposal
Paint and dried paint remainders must be disposed of in an
environmentally-friendly manner. Observe the manufactur-
er's instructions for disposal and the local regulations for haz-
ardous waste disposal.
Chemicals harmful to the environment may not be disposed of
into soil, groundwater or bodies of water. Never pour chemicals
harmful to the environment into the sewerage system!
Maintenance
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
Bosch Power Tools