Normal Washer Sounds; Options; Modifiers - Whirlpool WHP1000SQ Guide D'utilisation

Normal Washer Sounds

As with any new product, you will hear sounds that you are not
accustomed to. You may hear various sounds when the door is
locked and unlocked, and during the washing, rinsing, and spinning
process. Between changes in wash actions, there will be
momentary pauses. You will hear water spraying and splashing
during the wash and rinse cycles. These new sounds and pauses
are part of normal washer operation.

Options

You can customize your wash by adding options to your cycle
selections. You can add or change an option after starting a cycle
anytime before the selected option begins. Not all options are
available with all cycles. Available options will glow amber. Current
selections will glow green. If an option is unavailable with a selected
cycle, the light will not illuminate.
■ See the "Laundry Guide" for an overview of possible options for
each Wash Cycle selection.
■ You can select more than one option for a cycle. Some options
cannot be added to some cycles. For example, Deep Clean
cannot be added to the Quick Wash cycle.
■ If an option is unavailable with a selected cycle, there will be
3 short tones, and the light for that option will not glow when
selected.
Delay Wash
To begin the wash cycle later, select DELAY WASH until the desired
delay time (in hours) shows in the Estimated Time Remaining
display, and then select START. The countdown to the wash cycle
will show in the display window, and the button indicator will blink
until the cycle begins.
IMPORTANT: When delaying a cycle, use only powdered
detergents in the high efficiency "HE" detergent compartment
since liquid detergents may seep out of the compartment during
Delay Wash, before the wash cycle begins.
TumbleFresh™ option
Use this option when you are not able to remove your clothes,
soon after the wash cycle ends. This option provides periodic
tumbling for up to 6 hours to help freshen your clothes. During this
time, the "Done" indicator remains activated, the door remains
locked, and the TumbleFresh™ indicator light will flash. The
TumbleFresh™ option will automatically stop and the door lock
will be released after this time expires, or if you press PAUSE/
CANCEL at anytime to unload your laundry.
16
EcoBoost™ option
The EcoBoost™ option allows you to increase your energy savings
on the higher temperature cycles (Whitest Whites and Heavy Duty)
while maintaining cleaning performance by lengthening the wash
time by 10 minutes.
NightQuiet™ option
In this option, the washer will sense vibration in the wash cycle and
may adjust the spin speed to lower sound levels generated during
the spin.
Deep Clean with Steam
Use this option for heavily soiled loads that need improved stain
treatment, loads with multiple types of stains, or loads you
suspect as having stains, but are afraid may have been missed
(no sorting or searching for stains). When Deep Clean with Steam
is selected, the water temperature of the selected wash cycle is
automatically set to warm. The water will then be slowly heated to
the temperature selected, along with steam, to aid in stain removal.
This option will provide optimal removal of organic stains such as
blood and grass.
Cycle Signal
This signal is helpful when you are removing items from the
washer as soon as it stops. Press CYCLE SIGNAL to select Loud,
Soft, or Off. To activate/deactivate button sound hold cycle signal
button for 3 seconds.

Modifiers

Preset cycle settings of Water Temperature, Spin Speed, Soil
Level, and Rinse can be changed. You can change a modifier after
starting a cycle anytime before the selected modifier begins. Not all
modifiers are available with all cycles and options. Available options
will glow amber. Current selections will glow green. If a modifier is
unavailable with a selected cycle, the light will not illuminate.
NOTE: The panel shown below may be different from that of your
model.
■ To change the water temperature, select the WATER TEMP
button until the desired setting glows green.
■ To change the spin speed, select the SPIN SPEED button
until the desired setting glows green.
■ To change cycle time, select SOIL LEVEL button until the
desired setting glows green.
■
To change the rinse, select RINSE button until the desired
setting glows green.