Introduction; General Notes; Safety Instructions - Scheppach TIGER 3000VS Traduction Du Manuel D'origine

1. Introduction

Manufacturer:
Scheppach Fabrikation von Holzbearbeitungsmaschinen
GmbH
GÜnzburger Straße 69
D-89335 Ichenhausen / BRD
Dear customer,
we wish you a pleasant and successful working experi-
ence with your new scheppach circular wet grinding
machine.
According to the applicable product liability law the
manufacturer of this device is not liable for damages
which arise on or in connection with this device in case
of:
• improper handling
• non-compliance with the instructions for use
• repairs by third party, non authorized skilled workers
• installation and replacement of non-original spare
parts
• improper use
• failures of the electrical system due to the non-
compliance with the electrical specifications and the
VDE 0100, DIN 57113 / VDE 0113 regulations
Recommendations:
Read the entire text of the operating instructions prior
to the assembly and operation of the device.
These operating instructions are intended to make it
easier for you to get familiar with your device and uti-
lize its in tend ed possibilities of use.
The operating instructions contain important notes on
how to work safely, properly and economically with
your machine and how to avoid dangers, save repair
costs, reduce downtime, and increase the reliability
and working life of the machine.
In addition to the safety regulations contained herein,
you must in any case comply with the applicable regu-
lations of your country with respect to the operation of
the machine.
Put the operating instructions in a clear plastic folder
to protect them from dirt and humidity, and store them
near the machine. The instructions must be read and
carefully observed by each operator prior to starting
the work. Only persons who have been trained in the
use of the machine and have been informed on the
related dangers and risks are allowed to use the ma-
chine. The required minimum age must be met.
In addition to the safety notes contained in the present
operating instructions and the special regulations of
your country, the generally recognized technical rules
for the operation of wood working machines must be
observed.

2. General Notes

• When you unpack the device, check all parts for pos-
sible transport damages. In case of complaints the
supplier is to be informed immediately.
• Complaints received at a later date will not be ac-
knowledged.
• Check the delivery for completeness.
• Read the operating instructions to make yourself fa-
miliar with the device prior to using it.
• Use only original parts for accessories as well as for
wearing and spare parts. Spare parts are available
from your specialized dealer.
• Specify our part numbers as well as the type and
year of construction of the device in your orders.
Specifications
Dimensions LxWxH mm
Tool rest ø mm
Grinding stone ø mm
Idle-running speed - grinding
stone 1/min.
Cutting speed m/sec.
Weight kg
Drive
Motor V
Input P1 W
Output P2 W
Motor speed 1/min.
Operating mode
Current rating A
Subject to technical modifications!

3. Safety Instructions

Operators' Training
• Pass the safety instructions to all persons working
with the machine.
• The operator must be at least 18 years old. Trainees
must be at least 16 years old, but are only allowed to
use the machine under supervision.
• Persons operating the machine must not be distract-
ed.
• Keep away children from the machine if it is con-
nected to the mains.
• Always wear tight clothes. Remove jewelry, rings,
and wrist watches.
• Observe all safety instructions and warnings on the
machine and maintain them in a readable state.
• Be careful when working with the machine: the rotat-
ing grinding tool may cause injuries of fingers and
hands.
Stability
• Make sure the machine is installed on a firm ground
with sufficient stability.
• Make sure the workplace is sufficiently illuminated.
Mains Connection of the Machine
• Check the mains connecting lines. Do not use defec-
tive lines. See electrical connection.
• Pay attention to the direction of rotation of the motor
and the tools. See electrical connection.
• Installations, repair, and maintenance work relating
to the electric installation may only be performed by
specialists.
• Turn off the machine before you repair failures. Dis-
connect the mains plug.
• Turn off the motor when you leave the workplace.
Disconnect the mains plug.
380x290x390
12
250
90-150
1,2-2
13
230 – 240
180
80
1950-3250
S1
0,95
english 11