Jonsered LM2146M Manuel D'instructions page 13

ANNUALLY CARRY OUT THE FOLLOWING:
1. Sharpening and balancing the cutter blade.
Remove the spark plug lead. Remove the cutter
blade and take it to a service workshop for sharpening
and balancing. When reassembling the blade ensure
that the retaining washer is flat and not dished, tighten
the bolt to a torque of 35-40 Nm. (V)
2. Change the oil after each season or after 25 hours.
Run the engine until warm. Remove the spark plug
lead. Remove the blade to gain access to the oil drain
plug, open the drain plug underneath the mower and
let the oil run out. Refit the plug and fill with new oil,
SAE 30. (W)
3. The engine brake cable should always be adjusted to
stop the engine within 3 sec. CAUTION! For adjustment
contact your authorized service dealer. (X)
4. Remove cover and take out the air filter.(Z1 & Z2)
5. Clean the filter with warm, soapy water and dry
thoroughly. Add 2-3 spoons of oil, distributing evenly
throughout the filter.
Transport
Remove the spark plug lead
Loosen the wire/cable from the handle before carefully
folding it. Avoid damaging the wire/cable
Empty the petrol tank. The machine must be drained of
oil and fuel when moving it by public transport.
Service
When ordering spare parts, always quote the mower's
product number. Always check oil level after service.
At the End of the Mowing Season
1. Replace blade, bolts, nuts or screws, if necessary.
2. Clean your lawnmower thoroughly.
3. Ask your local Service Centre to clean the air filter
thoroughly and carry out any service or repairs required.
4. Drain engine of oil and petrol.
Storing your Lawnmower
1. Do not store your lawnmower immediately after use.
2. Wait until the engine has cooled to avoid a potential
fire hazard.
3. Clean your lawnmower
4. Store in a cool, dry place where your lawnmower is
protected from damage.
Service Recommendations
Your product is uniquely identified by a silver and black
product rating label.
We strongly recommend that your product is serviced at
least every twelve months, more often in a professional
application.
Engine Maintenance Schedule
Follow the hourly or calendar intervals, whichever occur
first. More frequent service is required when operating in
adverse conditions
First 5 hours - Change oil.
Every 5 hours or daily - Check oil level.
Clean finger guard. Clean around muffler.
Every 25 hours or every season - Change oil if operating
under heavy load or high ambient temperature. Service
air cleaner.
Every 50 hours or every season - Change oil. Inspect
spark arrester, if equipped.
Every 100 hours or every season - Clean cooling
system . Replace spark plug.
Clean more often under dusty conditions, or when
airborne debris is present or after prolonged operation
cutting tall, dry grass.
Engine Servicing & Guarantee
The engine fitted to your lawnmower is guaranteed by
the Engine Manufacturer.
Fault Finding
Engine Will Not Start
1. Ensure Operator Presence Control is in the start
position.
2. Check that there is sufficient fuel in the tank and the
cap air vent is clear.
3. Remove and dry the spark plug.
4. Petrol may be stale. Replace. Once petrol has been
replaced, it may take a little time for fresh petrol to
Maintenance
filter through.
5. Check that the blade bolt is tight. A loose bolt could
cause difficult starting.
6. If the engine will still not start, immediately disconnect
the spark plug lead.
7. CONSULT YOUR LOCAL APPROVED SERVICE
CENTRE.
Lack of Engine Power and/or Overheating
1. Disconnect the spark plug lead and allow the engine
to cool down.
2. Clean grass clippings and debris from around the
engine and air inlets and the underside of the deck.
3. Clean the engine air filter (Ask your local Approved
Service Centre to clean the engine air filter thoroughly).
4. Petrol may be stale replace. Once petrol has been
replaced, it may take a little time for fresh petrol to
filter through.
5. If the engine still lacks power and/or is overheating,
immediately disconnect the spark plug lead.
6. CONSULT YOUR LOCAL APPROVED SERVICE
CENTRE.
Excessive Vibration
1. Disconnect the spark plug lead.
2. Check that the blade is correctly fitted.
3. If the blade is damaged or worn replace it with a new one.
4. If vibration persists, turn the blade through 180
first loosening the blade bolt, turning the blade and re-
tightening the blade bolt.
5. If vibration persists, immediately disconnect the spark
plug lead.
6. CONSULT YOUR LOCAL APPROVED SERVICE
CENTRE.
ENVIRONMENTAL INFORMATION
Husqvarna Outdoor Products are manufactured under
an Environmental Management System (ISO 14001)
using, where practical, components manufactured in the
most environmentally responsible manner, according to
company procedures, and with the potential for recycling
at the end of the products' life.
Packaging is recyclable and plastic components
have been labelled (where practical) for categorised
recycling.
Awareness of the environment must be considered
when disposing of end-of-life' product.
If necessary, contact your local authority for disposal
information.
DISPOSAL OF FUELS AND LUBRICATING OILS
Wear protective clothing when handling any fuels
and lubricants.
Avoid contact with skin.
Remove petrol and engine oil before transporting
the product.
Contact your local authority for information of your
nearest Recycling/Disposal Station.
Do NOT dispose of used fuels/oils with
household waste
Waste fuels/oils are harmful, but can be
recycled and should be disposed of through
the recognised facilities.
Do NOT dispose of used fuels/oils to water.
Do NOT incinerate
ENGLISH - 3
0 by