Changing Fahrenheit And Celsius Setting; Maintenance; General; Daily Cleaning - Hatco HCSBFR Série Manuel D'installation

OPERATION

Changing Fahrenheit and Celsius Setting

Use the following procedure to change between Fahrenheit
and Celsius on the display.
1. Press and hold the
programming mode. "PS" (password) will appear on the
display.
2. Press the key again. A numeric value will appear on
the display.
3. Press the or
on the display, then press the
4. Use the or key to scroll through the programmable
parameters until
5. Press the key to select

MAINTENANCE

General

Remote Hot/Cold Built-In Shelves are designed for maximum
durability and performance, with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and
allow unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not clean unit when it is energized or hot.
• This unit is not "jet-proof" construction. Do not use
jet-clean spray to clean this unit.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
FIRE HAZARD: Do not use harsh chemicals such as
bleach (or cleaners containing bleach), oven cleaners, or
flammable cleaning solutions to clean this unit.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
Make sure to clean and sanitize stone surface properly
after deep cleaning the surface using abrasives and before
placing food product on unit.
key for three seconds to access
key until the number "22" appears
key.
appears on the display.
.
6. Press the or
the desired setting. See below for the correct setting:
"0" = Displays Celsius
"1" = Displays Fahrenheit
If no key is pressed within 60 seconds, the display will
revert to normal operation and the current temperature of
the unit will be shown on the display.
7. Press the key to lock in the new setting.
8. Press and hold the
programming mode. The display will revert to show the
current temperature of the unit.
Do not use steel wool for cleaning. Steel wool will scratch
the finish.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Do not use harsh chemicals such as bleach, cleaners
containing bleach, or oven cleaners to clean this unit.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.

Daily Cleaning

To preserve the finish and maintain operation of the unit,
perform the following cleaning procedure daily.
1. Before turning on a HCSSBR, HCSSBFR, HCSSBX, or
HCSSBFX model each day, clean and sanitize the stone
shelf using a clean, damp cloth and a sanitizer approved for
food contact surfaces. If additional cleaning is necessary,
refer to the "Cleaning the Stone Surface" information in this
section.
2. At the end of each day:
a. Move the Power Switch to the center "O" (off) position
and allow the unit to cool/defrost.
b. Remove and wash all food pans, if present.
c. Clean the shelf using a clean cloth or sponge and mild
detergent. Use a plastic scouring pad to remove any
hardened food particles or mineral deposits.
d. Rinse the shelf thoroughly with hot water to remove all
detergent residue.
e. Wipe down shelf with a clean, sanitized cloth to remove
the detergent residue. Repeat until all detergent residue
is gone and the shelf is clean.
f. Wipe dry the entire unit using a non-abrasive, dry cloth.
g. Wipe down the outside of the louvered or grill-style
panels installed in the cabinet ventilation openings.
22
English
key within 60 seconds to scroll to
key for three seconds to exit
NOTICE
Form No. HCSRM-0817