Installation; General; Preparing The Installation Site - Hatco HCSBFR Série Manuel D'installation

English

General

Remote Hot/Cold Built-In Shelves are shipped from the factory
as components that require installation and connection. Use
the following procedures to install each component and make
the appropriate connections.
NOTE: Make sure the installation location provides enough
room for the condensing unit and the remote mounted
control enclosure.
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Unit is not weatherproof. Locate unit indoors.
• Remote control enclosure must be mounted on vertical
wall and installed in vertical position. Mounting remote
control enclosure in horizontal position may result in
collection of liquids and lead to electric shock.
FIRE HAZARD: Install condensing unit with a minimum of
6" (152 mm) of space between all sides of unit and any
combustible surfaces.
CAUTION
Locate unit at proper counter height in an area that is
convenient for use. The location should be strong enough
to support the weight of unit and contents.
NOTICE
Transport and install unit in upright position only. Failure
to do so may result in damage to refrigeration system.
This unit is designed for use in environments where
ambient temperature is between 65°F (18°C) and 86°F
(30°C).
When shipped during cold weather months, store unit
for at least 10 hours in an environment where ambient
temperature is between 65°F (18°C) and 86°F (30°C) to
prevent compressor and/or refrigerant line damage. If unit
is turned on and there is excessive noise and vibration,
turn off immediately and allow additional warmup time.
Provide louvered or grill-style openings with a minimum
size of 12" x 12"/144 square inches (31 x 31 cm/961 square
cm) in the cabinetry in front of and behind the condensing
unit for proper ventilation. Failure to provide adequate air
flow through the condensing unit may cause unit failure
and will void the unit warranty.
Do not recirculate exhaust air inside cabinet when multiple
condensing units are installed together. Intake air should
enter from outside of cabinet.
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
Do not locate unit in an area subject to excessive
temperatures or grease from grills, fryers, etc. Excessive
temperatures could cause damage to the unit.
Form No. HCSRM-0817
Damage to any countertop material caused by heat or cold
generated from Hatco equipment is not covered under
the Hatco warranty. Contact manufacturer of countertop
material for application information.
All Remote Hot/Cold Built-In Shelves are shipped in a shipping
frame for protection and stability. Keep the unit in the shipping
frame until the unit and the installation site are completely
prepared for the unit to be installed.
Survey the installation site. Take into account the need for
louvered or grill-style openings in the cabinetry to provide
proper ventilation for the condensing unit as well as access to
the control panel. One of these ventilation openings must be in
front of the condensing coils with the other on the opposite side.
If multiple condensing units are installed in the same counter,
each unit should intake cool air and expel hot air.
1. Remove all external packaging from the unit.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
2. Remove tape, protective packaging, and literature from all
surfaces of the unit.

Preparing the Installation Site

1. Prepare the appropriate opening in the countertop for the
unit being installed.
• For top mounted HCSBFR and HCSBFX models, refer
to the "Countertop Cutout Dimensions — Top Mounted
Units," in this section.
• For bottom mounted HCSSBR, HCSSBFR, HCSSBX,
and HCSSBFX models, refer to the "Countertop Cutout
and Mounting Bolt Dimensions — Bottom Mounted
Units," in this section.
2. Cut and drill the appropriate holes in the vertical surface
where the control enclosure will be installed. Refer to the
"Installing the Control Enclosure Remotely" procedure for
cutout dimensions.
• The installation depth required for the control enclosure
is 10" (254 mm).
3. Make structural modifications or add bracing underneath
the countertop to ensure the countertop will support the
weight of the unit and its contents.
4. Install the unit. Refer to the appropriate procedure in this
section for either a top mounted unit or a bottom mounted
unit.
13

INSTALLATION

NOTICE