Exo Terra Reptile Dome NANO Mode D'emploi page 4

use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without
supervision.
5. Always unplug an appliance from an outlet when not in use,
before putting on or taking off parts, and before cleaning.
Never yank cord to pull the plug from the outlet. Grasp the plug
and pull to disconnect.
6. Do not use the appliance for other than intended use. The use
of attachments not recommended or sold by the appliance
manufacturer may cause an unsafe condition.
7. Do not install or store the appliance where it will be exposed to
weather or to temperatures below freezing. Do not expose the
unit to direct sunlight.
8. If an extension cord is necessary, ensure the connection
is watertight and dust proof. A cord with a proper rating
should be used. A cord rated for less amperes or watts than
the appliance rating may overheat. Care should be taken to
arrange the cord so that it will not be tripped over or pulled.
The connection should be carried out by a qualified electrical
installer.
9. Keep unit out of reach of children. Keep unit away from
curtains or other flammable objects.
10. Make sure the appliance is securely installed before operating
it.
SAVE THESE INSTRUCTIONS
Only close adherence to these installation, electrical and
maintenance guidelines will ensure the safe and efficient use of
this appliance.
6
INSTALLATION (Diagram p.2)
1. Glass surface preparation: surface temperature for
application should be no lower than 60°F degrees (16°C) and
not higher than 85°F degrees (29°C). If climate will not permit,
move unit to appropriate conditions. Area to receive tape should
first be thoroughly cleaned with a liquid detergent and warm
water solution. Rinse with clean water and dry completely. A
final wipe with 50/50 alcohol/water is highly recommended for
best results (use a clean, lint-free cloth). Ensure surface is dry
and residue free before proceeding. Note: The position of the
adhesive support base cannot be changed after it has been
affixed.
2. With the protective backing still intact, place the adhesive
support base on the back or the side of the terrarium to
determine its final position and mark the position with a wax
pencil or other marker.
3. Remove the protective backing and carefully fit the adhesive
support base within the marked area.
4. Press the adhesive tape firmly and evenly against the glass
panel, while gently twisting, to ensure proper adhesion. Make
sure no air bubbles are showing. Once in place, the adhesive
support base should not be removed!
5. Allow the adhesive tape bond to cure for 24 hours! Let the
Reptile Dome NANO rest on the terrarium mesh for 24 hours
to allow the tape bond to cure properly before the dome is
suspended and the weight of the dome can exert pressure on
the support base. INSTALL LIGHT AFTER 24 HOURS TO ALLOW
THE TAPE BOND TO CURE PROPERLY
6. Adjust the height and tighten the screw of adhesive supporting
base when the Exo Terra Reptile Dome NANO is suspended
above the terrarium at the desired height.
7. Ensure that the light's focal point is not positioned above any
plastic parts of the terrarium or screen cover to prevent damage.
8. Screw light bulb into the Exo Terra Reptile Dome NANO (follow
maximum wattage guidelines: 40W Max.). TIP: apply a thin layer
of petroleum jelly to the threads on the base of the light bulb
before screwing it in. This will make it easier to unscrew the bulb
when it is time to replace it.
INSTALL LIGHT AFTER 24 HOURS TO ALLOW THE TAPE BOND TO
CURE PROPERLY
NOTE : FAILURE OF PROPER TAPE BONDING MAY BE ATTRIBUTED TO
ONE OF FOUR ISSUES:
1. Poor surface preparation and/or application.
2. Poor adhesive contact: exposed adhesive side of tape being
touched or contaminated.
3. Insufficient pressure being applied.
4. Lamp hung too soon, tape not fully cured.
GUARANTEE
This product is guaranteed for defective parts and workmanship
for a period of 2 years from the date of purchase. This guarantee is
valid with proof of purchase only. The guarantee is limited to repair
or replacement only and does not cover consequential loss, loss or
damage to livestock and personal property or damage to animate or
inanimate objects, irrespective of the cause thereof. This guarantee
is valid only under normal operating conditions for which the unit
is intended. It excludes any damage caused by unreasonable use,
negligence, improper installation, tampering, abuse or commercial
use. The warranty does not cover wear and tear or parts which
have not been adequately or correctly maintained. THIS DOES NOT
AFFECT YOUR STATUTORY RIGHTS.
RECYCLING
This item bears the selective sorting symbol for waste
electronic and electrical equipment (WEEE). This
means that the product must be handled pursuant
to European Directive 2012/19/EU in order to be
recycled or dismantled to minimize it's impact on
the environment. For further information please
contact your local or regional Authorities. Electronic
products not included in the selective sorting process are potentially
dangerous for the environment and human health due to the
presence of hazardous substances.
SERVICE
If you have any problems or questions about the operation of this
product, please let us try to help you before you return the product
to your dealer. Most problems can be resolved in store, but in the
unlikely event it cannot, please return the unit with a valid proof
of purchase to the retailer for a replacement under the two year
warranty. When you call (e-mail or write) our Customer Service
Department, please have all relevant information such as model
number and/or part numbers available, as well as the nature of the
problem: