Scheppach DP18VARIO Traduction De La Notice Originale page 17

Introduction
MANUFACTURER:
scheppach Fabrikation von
Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and
success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
WE RECOMMEND:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device.
The operating instructions are intended to help the user
to become familiar with the machine and take advan-
tage of its application possibilities in accordance with the
recommendations. The operating instructions contain
important information on how to operate the machine
safely, professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in your
country. Keep the operating instructions package with
the machine at all times and store it in a plastic cover
to protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only be
operated by persons who were instructed concerning the
operation of the machine and who are informed about
the associated dangers. The minimum age requirement
must be complied with. In addition to the safety require-
ments in these operating instructions and your country's
applicable regulations, you should observe the generally
recognized technical rules concerning the operation of
woodworking machines.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Device Description (Fig.1-2)
1. Machine foot
2. Column
3. Clamping handle
4. Drilling table
5. Motor
6. Speed adjustment lever (handle)
7. V-belt cover
8. Digital display
9. On and off switch
10. Handle
11. Folding swarf protector
12. Drill chuck (illustration may differ)
13. Roller support
14. Machine head
15. Working light/laser control panel
16. Depth indicator with stop
17. Crank handle
18. Drilling table holder
19. Hexagonal screw
20. Crank holder
21. Wing screws
22. Tapered mandrel
A. Hexagon spanner
B. Taper key
C. 4 mm Allen key
D. 3 mm Allen key
Unpacking
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the pack-
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
Intended use
The bench drill is designed for drilling in metal, wood,
plastic and tiles. Straight shank drills with a drilling di-
ameter from 3 mm to 16 mm can be used. The device
is intended to be used by do-ityourselfers. It was not
designed for heavy commercial use. The tool is not
to be used by persons. under the age of 16. Children
over the age of 16 may use the tool except under su-
pervision. The manufacturer is not liable for damage
caused by an improper use or incorrect operation of
this device. The bench-type circular saw is designed
for the slitting and cross-cutting of all types of timber,
commensurate with the machine's size. The machine
is not to be used for cutting any type of roundwood.
17 І 80