Technical Specifications - BFT X 130 Instructions D'utilisation

ENGLISH
Thank you for buying this product, our company is sure that you will be more
than satisfied with the product's performance. The product is supplied with
a "Warnings" leaflet and an "Instruction booklet". These should both be
read carefully as they provide important information about safety, installation,
operation and maintenance. This product complies with the recognised
technical standards and safety regulations. We declare that this product is
in conformity with the following European Directives: 89/336/EEC and 73/
23/EEC, 98/37/EEC (and subsequent amendments).
GENERAL OUTLINE
Compact sturdy electromechanical operator for balanced roll-up doors,
provided with electrical limit switches which can be adjusted on opening
and on closing.
Available in two versions, reversible (X130) and irreversible (X130EF), the
latter provided with electric brake.
For irreversible versions, the emergency manoeuvre is carried out by
means of a knob attached to a wire.
The operator supplied is suitable for 60mm shafts and 220mm drive pulleys.
If necessary, 42mm and 48mm reduction half bearings, as well as 200mm
drive pulleys are available.
GENERAL SAFETY
WARNING! An incorrect installation or improper use of the product
can cause damage to persons, animals or things.
• The "Warnings" leaflet and "Instruction booklet" supplied with this product
should be read carefully as they provide important information about
safety, installation, use and maintenance.
• Scrap packing materials (plastic, cardboard, polystyrene etc) according
to the provisions set out by current standards. Keep nylon or polystyrene
bags out of children's reach.
• Keep the instructions together with the technical brochure for future
reference.
• This product was exclusively designed and manufactured for the use
specified in the present documentation. Any other use not specified in this
documentation could damage the product and be dangerous.
• The Company declines all responsibility for any consequences resulting
from improper use of the product, or use which is different from that
expected and specified in the present documentation.
• Do not install the product in explosive atmosphere.
• The construction components of this product must comply with the following
European Directives: 89/336/CEE, 73/23/EEC, 98/37/EEC and subsequent
amendments. As for all non-EEC countries, the above-mentioned standards
as well as the current national standards should be respected in order to
achieve a good safety level.
• The Company declines all responsibility for any consequences resulting
from failure to observe Good Technical Practice when constructing closing
structures (door, gates etc.), as well as from any deformation which might
occur during use.
• The installation must comply with the provisions set out by the following
European Directives: 89/336/CEE, 73/23/EEC, 98/37/EEC and subsequent
amendments.
• Disconnect the electrical power supply before carrying out any work on
the installation. Also disconnect any buffer batteries, if fitted.
• Fit an omnipolar or magnetothermal switch on the mains power supply,
having a contact opening distance equal to or greater than 3mm.
• Check that a differential switch with a 0.03A threshold is fitted just before
the power supply mains.
• Check that earthing is carried out correctly: connect all metal parts for
closure (doors, gates etc.) and all system components provided with an
earth terminal.
• Fit all the safety devices (photocells, electric edges etc.) which are needed
to protect the area from any danger caused by squashing, conveying and
shearing, according to and in compliance with the applicable directives
and technical standards.
• Position at least one luminous signal indication device (blinker) where it
can be easily seen, and fix a Warning sign to the structure.
• The Company declines all responsibility with respect to the automation
safety and correct operation when other manufacturers' components are
used.
• Only use original parts for any maintenance or repair operation.
• Do not modify the automation components, unless explicitly authorised by
the company.
• Instruct the product user about the control systems provided and the
manual opening operation in case of emergency.
• Do not allow persons or children to remain in the automation
operation area.
• Keep radio control or other control devices out of children's reach, in order
to avoid unintentional automation activation.
• The user must avoid any attempt to carry out work or repair on the
8
- X130 - Ver. 01
INSTALLATION MANUAL
automation system, and always request the assistance of qualified
personnel.
• Anything which is not expressly provided for in the present instructions, is
not allowed.

TECHNICAL SPECIFICATIONS

Pulley diameter: ......................................... X130:220mm - X130P:200mm
Power supply: ....................................................... 230Va.c.±10% 50Hz (*)
Maximum weight: ... X130: 2000N (200 kg) .........X130P: 2200N (220 kg)
Absorbed power: ......... X130PEF/X130EF: 260W
Operation time: ....................................................................... max. 4 min
End-of-stroke revolutions: ...................................................................... 13
Output shaft revolutions: ............................................................ 11,8 min
Thermal protection: ........................................................................ present
Motor: ............................................................................ 2800 min
Capacitor for X130: ...................... 11µF 450V (230V): 45µF 250V (110V)
Capacitor for X130 EF: .............. 12,5µF 450V (230V): 50µF 250V (110V)
Insulation class: ........................................................................................ F
Circuit-breaking activation temperature: ................. 160°C (self-resetting)
Reduction gear lubrication: .......................................... Permanent grease
Max. torque X130-X130 P: ............................................................ 125 Nm
Max. torque X130 EF-X130 PEF: ................................................. 113 Nm
Impact reaction (safety edge): ........................................ stop and reverse
Limit devices: ................. Electromechanical, incorporated and adjustable
Maximum no. manoeuvres in 24h: ........................................................... 8
Working temperature: ......................................................... -20°C ÷ +50°C
Degree of protection: ........................................................................... IP20
Operator weight: ...................................................................... 60N (~6 kg)
Noise level: ............................................................................... : <70dB(A)
Torque for reversibility (brake not fitted or released) ........................ 4Nm
Dimensions: ................................................................................ See fig. 1
(*) Special power supply voltages available on request.
INSTRUCTIONS MOD. K130/EF
Electro-mechanic made up of:
E - Electric brake with release mechanism.
M - Single-phase motor 2 poles protected by a heat circuit.
R - Epicycloidal reduction unit 1/36
C - Rolling gate-opener casing.
F - Limit switch.
P - Drive pulley.
FOR THE PROPER INSTALLATION CAREFULLY OBSERVE THE
FOLLOWING POINTS:
CHOICE OF THE TYPE OF ROLLING GATE
Measure:
- the surface or weight of the gate.
- the diameter of the spring box.
- the diameter of the spring box shaft.
Decide whether the the germotor consents the perfect closing of the rolling
gate and therefore must be provided with an electric brake, then choose the
suitable model according to the table A.
N.B. For capacities major to the ones specified in the table, apply a torque
of K130 on the same spring-holding post. For electric connection, see Fig 18.
It the shaft of the rolling gate has a diameter of 42 mm. or 48 mm. instead
of the standard one of 60 ask for the special reduction half bearings "S"
(fig.1).
All the models without electric brake are prearranged for the application of
the latter, which can be supplied as optional..
PREARRANGEMENT OR THE ROLLING GATE
Before installing the rolling gate check that it smoothly slides by rolling it up
and and down manually.
If there are any problems we advise to first check the greasing of the slide
tracks R (fig. 3) and that the rolling gate be properly balanced otherwise
change the spring boxes S (fig. 3).
MOUNTING OFTHEGEARMOTOR UNIT
- Open up the two parts of the drive pulley P (fig. 4) removing the screws V.
- Place the gearmotor unit at the center of the spriny box shaft and fasten
lightly it to the bracket S with the screws V and the nut D (fig. 5).
- Rotate the gearmotor unit 90° (fig. 6). Lock the bracket S and drill a hole
into the rolling gate shaft in correspon dance with slot A, then complete the
fas-tening by inserting screw V in the hole so as to totally block the rotation
of the gearmotor unit.
- Make sure that with rolling gate closed the cursor C is to be near the limit
X130EF: 1800N (180 kg) ....X130PEF: 2000N (200 kg)
X130P/X130: 300W
-1
-1
2 poles