Rotel RC-1572 Manuel De L'utilisateur page 16

16
NOTE: These settings are stored permanently even after the RC-1572
is powered off.
• BALANCE: Changes left/right balance (For more information on Balance
sections).
NOTE: This setting is stored permanently even after the RC-1572 is
powered off.
• DIMMER: Dims the display.
NOTE: This setting is stored permanently even after the RC-1572 is
powered off.
• POWER LED: Dims the Power LED on the front panel.
NOTE: This setting is stored permanently even after the RC-1572 is
powered off.
• POWER ON MAX VOLUME: This sets the maximum volume level when
the unit is turned ON. "45" is the factory default.
NOTE: Power On Max Volume settings do not apply to sources
configured with Fixed Gain.
• POWER OPTION: Enables the RC-1572 to be controlled via the network
port when attached to an automation system. The power consumption is
higher in Quick Power mode. If network control is not required select the
Normal Power mode. "Normal" is the factory default.
Valid settings include: Normal, Quick.
NOTE: When the POWER OPTION is configured to Quick, the RC-
1572 will consume additional power in standby mode.
• USB POWER: This option allows the rear panel USB connector to provide
power, even when the RC-1572 is in standby mode.
To enable the continuous power mode select the ALWAYS option. To provide
power only when the RC-1572 is powered on, select the NORMAL option.
The default for USB POWER is set to NORMAL.
NOTE: The front panel power button must be in the ON position to
supply power to the rear panel USB connector.
NOTE: When the USB POWER is configured to ALWAYS the RC-1572
will consume additional power in standby mode to supply USB power.
• AUTO POWER OFF: The RC-1572 can be configured to automatically
power off if unused for a specified period. If no changes are made to the
unit within the specified "Auto Power Off" timer the unit will automatically
go to STANDBY mode. The Auto Power Off timer will be restarted if
changes are made to the volume, source or playback. The default for
Auto Power Off is set to DISABLE.
Valid settings include: DISABLE, 1 HOUR, 2 HOURS, 5 HOURS, 12 HOURS.
• FIXED GAIN: Configures a Fixed Volume level for a specified input. To
enable this feature press the +/- buttons to select the desired fixed volume
level for Aux, USB, PC-USB, Optical 1, Optical 2, Coax 1, Coax 2 or
Bluetooth. When enabled and the input with a Fixed Volume is selected,
the Volume level will immediately be set to the specified level.
Valid settings include: VARIABLE, FIXED 01-95, FIXED MAX.
• AUX VOL: VARIABLE (disabled) is factory default.
• USB VOL: VARIABLE (disabled) is factory default.
• PC-USB VOL: VARIABLE (disabled) is factory default.
• OPT1 VOL: VARIABLE (disabled) is factory default.
• OPT2 VOL: VARIABLE (disabled) is factory default.
• COAX1 VOL: VARIABLE (disabled) is factory default.
• COAX2 VOL: VARIABLE (disabled) is factory default.
• BTOOTH VOL: VARIABLE (disabled) is factory default.
NOTE: The Volume knob on the front panel and Volume +/- buttons
on the IR remote are disabled when the volume is Fixed. To disable this
feature set the Fixed Volume level to "Variable".
• PC-USB AUDIO CLASS: Changes supported PC-USB Audio Class of the
attached device.
NOTE: Some computers attached to the PC-USB do not support USB
Audio Class 2.0 and do not support 32/384 audio playback. If needed
the PC-USB can be configured for USB Audio Class 1.0. Please consult
your computer operating system for details.
• NETWORK: Shows the network connection status and to view/configure
the network settings. If the network is properly configured and attached,
"Connected" will be displayed. To view or modify the network settings,
press the ENTER button.
The RC-1572 supports both DHCP and STATIC IP addressing. Select the
desired IP address method and press ENTER.
If DHCP is selected you can refresh IP address by pressing ENTER or press
MENU to view IP address information. Press the MENU button to toggle
through IP address settings. If the IP address is renewed the network will
be tested and connection status reported.
If STATIC IP address mode is selected you must configure all settings for the
network including IP Address, Subnet Mask, Gateway and DNS Server.
Use the up/down/left/right arrow buttons or the +/- buttons to adjust
the values and press ENTER to move to the next value. When the proper
IP information is configured press MENU to go to the next setting. After
entering the STATIC IP address information the network will be tested and
connection status reported.
NOTE: For more information regarding network connection please
contact your authorized Rotel dealer.
NOTE: A network connection is not required for the RC-1572 to
operate.
RC‑1572 Stereo Control Amplifier