EINHELL KGS 205-H Mode D'emploi page 14

Anleitung 06.11.2001 11:39 Uhr
GB
7. Assembly
A.) Adjusting the saw (Fig. 2)
While pressing down lightly on the machine head
(4), pull the lock pin (16) out of the motor holder
to disengage the saw from its bottom working
position.
Swing up the machine head until the retaining
hook latches home.
The machine head (4) can be tilted a max. 45° to
the left by undoing the clamping screw (13) with
the hex wrench (25) or knob (20).
Check that the voltage marked on the rating plate
is the same as your mains voltage and connect
up the machine.
B.) 90° cross-cuts and 0° rotary table (Fig. 3)
Press the main switch (3) to turn on the saw.
Caution! Position the material firmly on the
machine bed so that it cannot move about while it
is being cut.
After switching on the saw, wait for the blade (5)
to reach its maximum speed.
Press the release button (1) and lower the
machine head by its handle (2) smoothly and with
slight pressure down through the workpiece to
make the cut.
When the cut is completed, return the machine to
its top parking position and let go of the On/Off
switch.
Caution! A return spring causes the machine
head to rise automatically at the end of the cut.
Do not let go of the handle (2) as soon as the cut
is completed but steady the machine head and
allow it to rise slowly.
C.) Precision adjustment of the stop for 90°
cross-cuts (Fig. 4)
Lower the machine head (4) and fix with the lock
pin (16).
Slacken the clamping screw (13).
Place the stop angle (A) between the saw blade
(5) and the rotary table (8).
Slacken the counter nut (17) and adjust the
setting screw (12) until the angle between the
saw blade (5) and the rotary table (8) equals 90°.
Re-tighten the counter nut (17) to fix the machine
in this setting.
14
Seite 14
D.) 90° cross-cuts and 0°-45° rotary table (Fig. 5)
The KGS 205-H can be used to make angled cuts of
0°-45° relative to the stop rail on the left and right
side.
Undo the rotary table (8) by slackening the two
lock screws (19) on the stop rail.
Turn the rotary table (8) by its handle (2) to the
angle you want, i.e. the mark (a) on the rotary
table has to comply with the required angle
dimension (B) on the base plate (9).
Re-tighten the two lock screws (10) to fix the
rotary table (8) in position.
Make the cut as described in Section B.).
E.) Mitre cuts 0°-45° and rotary table 0° (Fig. 6)
The KGS 205-H can be used to make mitre cuts of
0°-45° relative to the machine bed on the left side.
Lift the machine head (4) to its top position.
Fix the rotary table (8) in 0° position.
Undo the clamping screw (13) and tilt the
machine head (4) by its handle (2) to the left until
the mark (a) on the machine head points to the
required angle dimension (b) of the support (21).
Re-tighten the clamping screw (13) and make the
cut as described in Section B.).
F.) Precision adjustment of the stop for 45° mitre
cuts (Fig. 7)
Lower the machine head (4) and fix with the lock
pin (16).
Fix the rotary table (6) in 0° position.
Undo the clamping screw (13) and tilt the
machine head (4) by its handle (5) to an angle of
45° on the left.
Place the 45° stop angle (A) between the saw
blade (5) and the rotary table (8).
Slacken the counter nut (18) and adjust the
setting screw (11) until the angle between the
saw (5) and the rotary table (8) equals exactly
45°.
Re-tighten the counter nut (18) to fix the machine
in this setting.