Electrical Safety; Start-Up Instructions - Jacuzzi J-LXL Manuel D'installation Et Utilisation Et Entretien

I
Keep hair, hair clips, and other objects, such as necklaces,
far away from the suction nozzles, filters, and the skimmer
cover. Make certain that children do not play or swim near
this equipment.
I
Do not sit on the suction nozzles, filters or the skimmer
cover. Make certain that children do not play or swim near
this equipment.
I
When the spa is in use, do not use any electrical appliance,
unless such appliances are built-in by the manufacturer.
I
The water in a spa should never exceed 40 °C. Lower water
temperatures are recommended for young children, pregnant
women and when spa use exceeds 10 minutes.
I
Persons with heart conditions, diabetes, high or low blood
pressure or other health problems must not use the spa without
first consulting their doctor.
I
The use of alcohol, narcotics or medicines may cause drowsi-
ness, and affect pulse rate, blood pressure and circulation. Avoid
using these substances before getting into the spa.
I
Do not use a spa immediately following strenuous exercise.
I
Be very careful when getting in an out of the spa. All of the sur-
faces are slippery when wet.
I
The spa is not intended for use in public places; always check
for any restrictions and/or regulations concerning the installation
and use of the apparatus in the area chosen.

Electrical safety

®
The MaxiJacuzzi are safe products, manufactured in compli-
ance with standards EN 60335-1, EN 60335-2-60, EN 12764
and tested during production to ensure user safety.
I
Installation must be performed by qualified personnel who
ensure compliance with current national regulations and who
are also authorized to issue a certificate of compliance with
proper installation procedures.
It is the responsibility of the installer to select materi-
als based on their intended use, to carry out work prop-
erly, to check the condition of the system that the unit
will be connected to and that it ensures safety of use
also concerning maintenance work and the possibility
to examine the system.
®
I
The MaxiJacuzzi are class "I" appliances and therefore they
must be permanently connected, without any intermediate
connections, to the electrical system and to the protection
system (earth system).
The electrical system of the building must be pro-
vided with a 0.03A differential switch and with an
efficient protection (earth) circuit. Check for proper
operation of the differential switch by pressing the TEST
button, which should trip.
Parts incorporating electrical components, except
remote control devices, must be located or fixed so
that they cannot fall into the spa.
Live components and equipment must be out of
reach of individuals in the spa.
I
For connection to the electrical mains, it is necessary to
install an omnipolar cut-off switch as per the values indicated
in the chapter "Electrical characteristics., which is to be
located in an area which is compliant with safety instructions
and which cannot be reached by the users who are using the
®
MaxiJacuzzi .
It is mandatory to comply with this instruction. Any other procedure
is prohibited.
I
The installation of electrical devices and equipment (sock-
ets, switches, etc.) near the MaxiJacuzzi
ance with legal standards and regulations in the country
where the MaxiJacuzzi
I
The disconnection devices must be installed in the power
supply network according to the installation instructions.
I
For the equipotential connection as required by specific
national standards, the installer must use the terminal provided
(standard EN 60335.2.60) in the electrical box, and marked
with the symbol .
must be established for all metallic masses surrounding the spa,
for example water and gas pipes, metallic platforms, and so on.

Start-Up Instructions

Read each step in its entirety before proceeding with that
step.
I
Remove any dirt from the spa. Although the spa shell has been
polished at the factory, you may want to treat it with a specially
formulated spa cleaner and wax available from your dealer prior
to filling the first time.
I
Filling the Spa
Remove the filter cover, then remove both filter cartridges as
outlined in section "Cleaning The Filters".
Position the end of the hose inside the filter connection and fill
the spa until the level of water covers all of the nozzles, without
however reaching the headrest.
Do not overfill your spa.
N.B.: If your water is extremely hard, it is preferable to fill halfway with hard
water and the rest of the way with softened water. Or, you may fill entirely
with hard water if you use a special water additive.
24
®
must be in compli-
®
is installed.
In particular, an equipotential condition