Electrical Safety; Start-Up Instructions - Jacuzzi J-LXL Manuel D'installation Et Utilisation Et Entretien

skimmer cover. Make certain that children do not play or
swim near this equipment.
I
Do not sit on the suction nozzles, filters or the skim-
mer cover. Make certain that children do not play or swim
near this equipment.
I
When the spa is in use, do not use any electrical appliance,
unless such appliances are built-in by the manufacturer.
I
The water in a spa should never exceed 40 °C. Lower water
temperatures are recommended for young children, pregnant
women and when spa use exceeds 10 minutes.
I
Persons with heart conditions, diabetes, high or low blood
pressure or other health problems must not use the spa without
first consulting their doctor.
I
The use of alcohol, narcotics or medicines may cause drowsi-
ness, and affect pulse rate, blood pressure and circulation. Avoid
using these substances before getting into the spa.
I
Do not use a spa immediately following strenuous exercise.
I
Be very careful when getting in an out of the spa. All of the
surfaces are slippery when wet.
I
The spa is not intended for use in public places; always check
for any restrictions and/or regulations concerning the installa-
tion and use of the apparatus in the area chosen.

Electrical safety

®
The MaxiJacuzzi are safe products, manufactured in com-
pliance with standards
60825-1: 1994+A1+A2, EN 55014-2, CISPR 22 CLASS B,
EN 61000-3-2, EN 6100-3-3
ensure user safety.
I
Installation must be performed by qualified personnel who
ensure compliance with current national regulations and who
are also authorized to issue a certificate of compliance with
proper installation procedures.
It is the responsibility of the installer to select mate-
rials based on their intended use, to carry out work
properly, to check the condition of the system that
the unit will be connected to and that it ensures
safety of use also concerning maintenance work
and the possibility to examine the system.
I ®
The MaxiJacuzzi are class "I" appliances and therefore
they must be permanently connected, without any inter-
mediate connections, to the electrical system and to the
protection system (earth system).
The electrical system of the building must be
provided with a 0.03A differential switch and
with an efficient protection (earth) circuit. Check
60335-1: 2002, 60335-2-60: 2003,
and tested during production to
for proper operation of the differential switch by
pressing the TEST button, which should trip.
Parts incorporating electrical components,
except remote control devices, must be located
or fixed so that they cannot fall into the spa.
Live components and equipment must be out of
reach of individuals in the spa.
I
For connection to the electrical mains, it is necessary to
install an omnipolar cut-off switch as per the values indi-
cated in the chapter "Electrical characteristics., which is to
be located in an area which is compliant with safety instruc-
tions and which cannot be reached by the users who are
using the MaxiJacuzzi
It is mandatory to comply with this instruction. Any other pro-
cedure is prohibited.
I
The installation of electrical devices and equipment (sock-
ets, switches, etc.) near the MaxiJacuzzi
ance with legal standards and regulations in the country
where the MaxiJacuzzi
I
The disconnection devices must be installed in the power
supply network according to the installation instructions.
I
For the equipotential connection as required by specific
national standards, the installer must use the terminal provided
(standard EN 60335.2.60) in the electrical box, and marked with
the symbol In particular, an equipotential condition must be
.
established for all metallic masses surrounding the spa, for
example water and gas pipes, metallic platforms, and so on.

Start-Up Instructions

Read each step in its entirety before proceeding with
that step.
I
Remove any dirt from the spa. Although the spa shell has
been polished at the factory, you may want to treat it with a spe-
cially formulated spa cleaner and wax available from your dealer
prior to filling the first time.
I
Filling the Spa
Remove the filter cover, then remove both filter cartridges as out-
lined in section "Cleaning The Filters".
Position the end of the hose inside the filter connection and fill
the spa until the level of water covers all of the nozzles, without
however reaching the headrest.
Do not overfill your spa.
N.B.: If your water is extremely hard, it is preferable to fill halfway
with hard water and the rest of the way with softened water. Or, you
may fill entirely with hard water if you use a special water additive.
Always fill the spa from both filter connections, so as to expel
air trapped in the pumps. Otherwise the air may remain trapped,
preventing the pumps from circulating the water.
24
®
.
®
must be in compli-
®
is installed.