Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Description, fig. 1
1
On-/off-switch
2
Adjuster wheel
3
Saw blade
4
Riving knife
5
Saw blade guard
6
Longitudinal stop
7
Table extension
8
Chipping bag
9
Transport wheel
10 Frame foot r.
11 Frame foot l.
12 Extraction hose
13 Table insert
Assembly
Any assembly and retooling work may only take place with
the mains plug removed.
Due to packaging reasons, this power tool is not comple-
tely assembled.
• Open the box and remove packaging and Styrofoam
parts.
• Remove the supplied components.
• Take the power tool from the box and put it on the
floor, using some cardboard as a base to protect the
surface.
Note: This power tool is heavy, two people should remove
it from the box.
Place all supplied parts on a flat surface. Group the same
parts.
Note: If connections are secured with a screw (round head
or hexagon head), hexagon nuts and washer, the washer
has to be fixed under the nut. Insert the screws from the
outside to the inside, secure connections with nuts from
the inside.
Note: During assembly, tighten nuts and screws only so
much that they cannot fall off. If you tighten nuts and
screws completely before the final assembly, the final as-
sembly cannot be carried out.
STEP 1. SET-UP, FIG. 2
1 Put the power tool on its side so that it stands on the
wheels and the rubber buffers.
2 Loosen the wing nuts (A).
3 Fold the frame (10) up and push it into the track.
4 Tighten the wing nuts again.
5 Repeat this process for the second frame (11).
STEP 2.
ASSEMBLY OF THE HANDWHEEL, FIG. 3
1 x
Handle
1 x
Allen key
1 x
Open-end spanner
1 Remove the lid of the handle using a screwdriver.
2 Remove the nut from the handle.
3 Place the nut into the recess specified for this at the
20
back of the handwheel.
4 Push the handle, with the screw at the front, into the
opening of the handwheel.
5 Tighten the handle's screw and close the handle's
opening again with the lid.
STEP 3.
ASSEMBLY OF THE TABLE EXTENSION, FIG. 4.1 – 4.2
1 x
Tabletop
2 x
Allen key
2 x
Open-end spanner
1 Pull the two shafts (B) of the chipping bag bracket
to the outside and remove the Allen screws and the
washers.
2 Attach the tabletop (2) by pushing it onto the shafts.
3 Make sure the ends of the shafts overlap with the
holes on the tabletop.
4 Fix the chipping bag bracket to the tabletop and tigh-
ten the screws.
5 Fix the tabletop (2) with two Allen screws (D) to the
shafts (B).
6 Fix the chipping bag (8) with the Velcro to the table
extension.
STEP 4.
ASSEMBLY OF THE RIVING KNIFE, FIG. 5.1 – 5.2
1
Riving knife
2
Saw blade guard
1 Remove the table insert.
2 Move the saw blade to its highest position by turning
the handwheel anti-clockwise for height adjustment.
Loosen the riving knife clamp (E). Fig. 5.1
3 Move the riving knife (4) to the specified position.
Make sure the flanges of the riving knife bracket en-
gage with the holes of the riving knife.
4 Tighten
the
riving
Fig. 5.2
5 Put the table insert back.
STEP 5.
USING THE TRANSPORT DEVICE, FIG. 8
1 Push the button underneath the handle (F) and pull
the telescope handle up until it engages.
2 Tilt the power tool slightly towards you so that it com-
pletely stands on the wheels.
3 Pull the power tool to the specified position and set
it up as described in Step 1.
4 Ensure a secure position and solid ground
STEP 6.
ASSEMBLY OF THE SAW BLADE GUARD, FIG. 6
1
Protective hood
1
Extraction hose
1 In order to assemble the saw blade guard (5), place
it over the riving knife (4) so that the screw fits into
the slot of the riving knife.
2 Tighten the wing nut sufficiently so that the saw blade
guard stays moveable but lifts when the work piece is
knife
clamp
(E)
again.
Publicité
Table des Matières
