Additional Safety Instructions - Dexter power SD1600VX Traduction Du Manuel D'origine

power tool with a switch that cannot be turned on
and off.
20 Important.
For your own safety you must only use the acces-
sories and additional units listed in the operating
instructions or recommended or specified by the
manufacturer. The use of mounted tools or accesso-
ries other than those recommended in the operat-
ing instructions or catalog may place your personal
safety at risk.
21 Repairs may only be carried out by a qualified
electrician
This electric power tool complies with the pertinent
safety information. Repair work must only be carried
out by a trained electrician, otherwise the equipment
may cause accidents.
22 Connect up the dust extraction system
If there are provisions for connecting up a dust
extraction system, make sure that such a system is
fitted and in use.

Additional safety instructions

• Switch the machine off immediately and pull the
power plug in an emergency.
• Follow all these safety instructions before and
while working with the saw.
• Do not use this saw to cut fire wood.
• Do not use this saw to cross-cut roundwood with-
out a suitable holding device.
• The machine is equipped with a safety switch to
prevent it from being switched on again acciden-
tally after a power failure.
• If you need to use an extension cable, make sure
its conductor cross-section is big enough for the
saw's power consumption. Minimum cross-section
1 mm .
2
• If you use a cable reel, the complete cable must
be pulled off the reel.
• Persons working on the machine should not be
distracted.
• After you have switched off the motor, never slow
down the saw blade by applying pressure to its
side.
• Only fit blades which are well sharpened and have
no cracks or deformations.
• Faulty saw blades must be replaced immediately.
• Never use saw blades which do not comply with
the data specified in this manual.
• It is imperative to make sure that all devices which
cover the saw blade are in good working order.
• Never dismantle the machine's safety devices or
render them inoperative.
• Damaged or faulty safety devices have to be
replaced immediately. Never cut workpieces which
are too small to hold securely in your hand.
• Never load the machine so much that it cuts out.
• Always press the workpiece firmly against the saw
table.
• Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
19 / 40
LEROY MERLIN – Rue Chanzy – Lezennes 59712 LILLE Cedex 9 – France
• Switch the machine off to rectify faults at the
blocked plug-in tool. - Pull the power plug- Re-
move the blockage. Important! Risk of injury from
saw blade! Wear gloves. Carry out a trial run with-
out a workpiece. Ensure that no unusual noise or
vibration occurs. Should this be the case, switch
the unit off and contact the manufacturer.
• Carry out retooling work, adjustments, measure-
ments and cleaning jobs only when the motor is
switched off. - Pull the power plug. -
• Before switching on, make sure that all keys and
wrenches have been removed from the tool.
• Switch off the motor and pull the power plug be-
fore you leave the workplace.
• Electrical installation work, repairs and mainte-
nance may only be carried out by persons who
have been specially trained.
• Refit all guards and safety devices immediately
after you have completed any repairs or mainte-
nance work.
• Be sure to observe the safety information and
operating and maintenance instructions issued by
the manufacturer, as well as the dimensions listed
in the Technical Data.
• It is imperative to observe the accident preven-
tion regulations in force in your area as well as all
other generally recognized rules of safety.
• Note the information published by your profes-
sional associations (VBG 7j).
• The saw is intended to be used indoors only.
• Workpieces that are smaller than the saw blade
guard can cause injuries to the hands or fingers.
Use suitable aids!
• Avoid cramped hand positions when guiding in the
workpiece and avoid positions in which slipping
could lead to your hand making direct contact with
the saw blade.
• Always fit the saw blade with the teeth facing in
the direction of the sawing table.
• Always set the correct blade tension to prevent the
saw blades from jerking.
• Be especially careful when cutting material with
irregular cut profiles.
• Exercise particular caution when cutting round ob-
jects such as rods and pipes. These can roll down
into the saw blade and cause the teeth to catch.
Use a wedge to brace such workpieces.
• The teeth can become caught in the kerf when
the workpiece is pulled back, especially if saw-
ings have filled in (blocked) the kerf. In this case,
you should switch the saw off, pull the power
plug, clear the kerf with a wedge, and remove the
workpiece.
• Never leave the work area without having already
switched the saw off. Wait until the saw stops
moving completely.
• Do not position, join, or construct any parts on the
work table while the saw is running.
• Only switch the saw on after you have removed
any remaining material and tools from the work
table. Leave only the workpiece to be machined
19 / 40