Introduction; Safety Information - Dexter power SD1600VX Traduction Du Manuel D'origine

1. Introduction

Important.
When using the equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating instructions and
safety information with due care. Keep these operat-
ing instructions in a safe place so that the informa-
tion is available at all times. If you give the equip-
ment to any other person, hand over these operating
instructions and the safety information as well. We
cannot accept any liability for damage or accidents
which arise due to a failure to follow these instruc-
tions and the safety information.

2. Safety information

CAUTION
Read all the safety information and instructions.
Any errors made in following the safety information
and instructions may result in an electric shock, fire
and/or serious injury.
Keep all safety information and instructions in a safe
place for future use.
2.1 General safety information on electric
power tools
Important. The following safety precautions must
be taken when using electric power tools in order to
protect the user from electric shocks and the risk of
injury and fire. Read and follow these instructions
before using the equipment.
1 Keep your work area tidy
Untidy work areas can result in accidents.
2 Check the ambient conditions
Do not expose electric tools to rain. Never use elec-
tric power tools in damp or wet locations. Provide
good lighting. Do not use electric power tools near
flammable liquids or gases.
3 Protect yourself against electric shocks
Avoid bodily contact with earthed parts, e.g. pipes,
radiators, cookers and refrigerators.
4 Keep children away
Do not allow other persons to touch the tool or cable,
keep them away from your work area.
5 Keep your electric power tools in a safe place
Unused tools must be stored in a dry, locked room
out of children's reach.
6 Do not overload your tools
They will work better and more safely within their
specified capacity range.
7 Use the right tools
Do not use tools or attachments which are too weak
for heavy duty work. Never use tools on jobs for
which they are not intended; for example, do not
use a hand-held circular saw to fell trees or lop off
branches.
8 Wear suitable work clothes
Never wear loose fittings clothes or jewelry. They
18 / 40
LEROY MERLIN – Rue Chanzy – Lezennes 59712 LILLE Cedex 9 – France
may get caught in moving parts. Rubber gloves and
non-slip shoes are recommended when working
outdoors. Wear a hair net if you have long hair.
9 Use personal safety equipment.
Wear safety goggles. Use a dust mask when work-
ing on dusty jobs.
10 Do not use the cable for purposes other than
that for which it is designed.
Do not carry the equipment by the cable and do not
use the cable to pull the plug out of the socket. Pro-
tect the cable from heat, oil and sharp edges.
11 Secure the workpiece
Use clamps or a vise to secure the workpiece. This
is safer than using your hand and also enables you
to operate the machine with both hands.
12 Do not overstretch
Avoid abnormal working postures. Make sure you
stand squarely and keep your balance at all times.
13 Take care of your tools
Keep your tools sharp and clean in order to work
well and safely. Follow the maintenance information
and the instructions for changing tools. Check the
power plug and cable on a regular basis and have
them replaced by an authorized specialist if they are
damaged. Check theextension cable regularly and
replace it if damaged. Keep handles dry and free
from oil and grease.
14 Pull out the power plug
When tools are not in use, before starting any main-
tenance work or when changing attachments such
as saw blades, drill bits and all kinds of mounted
tools.
15 Always remove keys and wrenches after use
Always check that keys, wrenches and other adjust-
ing tools have been removed before you switch on
the equipment.
16 Avoid unintentional starting
Never carry a tool with your finger on the switch but-
ton while the tool is connected to the power supply.
Make sure that the switch is turned off when con-
necting the tool to the power supply.
17 When using an extension cable outdoors
Check that it is approved for outdoor duty and is
marked accordingly.
18 Be alert at all times
Watch what you are doing. Use common sense
when working. Never use the tool when you are
distracted.
19 Check your tool for damage
Before using the tool again, check the safety devices
or any slightly damaged parts to ensure that they are
in good working order. Check that the moving parts
are working correctly, that they do not jam, and that
no parts are damaged. Make sure that all parts are
fitted correctly to ensure that the equipment remains
safe to use. Unless otherwise stated in the operating
instructions, damaged guards and parts have to be
repaired or replaced by a customer service work-
shop. Damaged switches have to be replaced by a
customer service workshop. Never use an electric
18 / 40