Intended Use; Safety Information - Dexter power 3901316953 Traduction Des Instructions D'origine

• Legs 4x (16)
• Long crossbar 2x (17)
• Short crossbar 2x (18)
• Support strut long 2x (21a)
• Support strut short 2x (21b)
• Cross member 4x (21c)
• Support frame 2x (16b)
• Bench extension 2x (8)
• Rubber feet 4x (16a)
• Rip fence (15)
• Saw blade guard (4)
• Transverse stop (7)
• Suction hose (5)
• Push stick (9)
• Ring spanner 10/21 mm (22a)
• Ring spanner 10/13 mm (22b)
• Hexagon head bolt 36x (19)
• Hexagon head nut 28x (20)
• Riving knife (6)

4. Intended use

The bench-type circular saw is designed for the slit-
ting and cross-cutting of all types of timber, commen-
surate with the machine's size.
The machine is not to be used for cutting any type of
roundwood.
The machine is to be used only for its prescribed pur-
pose.
Any use other than that mentioned is considered to
be a case of misuse. The user/operator and not the
manufacturer shall be liable for any damage or injury
resulting such cases of misuse.
The machine is to be operated only with suitable saw
blades.
It is prohibited to use any type of cutting-off wheel.
To use the machine properly you must also observe
the safety regulations, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the machine have to
be acquainted with this manual and must be informed
about its potential hazards. It is also imperative to ob-
serve the accident prevention regulations in force in
your area.
The same applies for the general rules of occupation-
al health and safety.
m Important!
When using the equipment, a few safety precau-
tions must be observed to avoid injuries and dam-
age. Please read the complete operating instructions
and safety regulations with due care. Keep this man-
ual in a safe place, so that the information is avail-
able at all times.
26 | GB
If you give the equipment to any other person, hand
over these operating instructions and safety regu-
lations as well. We cannot accept any liability for
damage or accidents which arise due to a failure to
follow these instructions and the safety instructions.
The manufacturer shall not be liable for any changes
made to the machine nor for any damage resulting
from such changes.
Even when the machine is used as prescribed it is
still impossible to eliminate certain residual risk fac-
tors. The following hazards may arise in connection
with the machine's construction and design:
• Contact with the saw blade in the uncovered saw
zone.
• Reaching into the running saw blade (cut injuries).
• Kick-back of workpieces and parts of workpieces
• Saw blade fracturing.
• Catapulting of faulty carbide tips from the saw
blade.
• Damage to hearing if essential ear-muffs are not
worn.
• Harmful emissions of wood dust when the machine
is used in closed rooms..
m Please note that our equipment has not been de-
signed for use in commercial, trade or industrial ap-
plications. Our warranty will be voided if the machine
is used in commercial, trade or industrial businesses
or for equivalent purposes.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.

5. Safety information

General power tool safety warnings
m WARNING: Read all safety warnings, instruc-
tions, illustrations and technical data provided
with this power tool. Failure to follow the warnings
and instructions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future refer-
ence.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.