Technical Data; Before Starting The Equipment; Attachment And Operation - Dexter power 3901316953 Traduction Des Instructions D'origine

• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual. In
doing so, your saw provides optimal performance.
• Hands may never enter the processing zone when
the machine is in operation. Release the handle
button and switch off the machine prior to any op-
erations.
• Prior to any adjustment, maintenance or service
work disconnect the mains power plug!

6. Technical Data

AC motor
Performance
Operating mode
Idle speed
Hart-metal blade
Number of teeth
Thickness riving knife
Table size
Cutting height max. 90°
Cutting height max. 45°
Height adjustment
Saw blade swivel
Suction port
Weight ca.
* operating mode S6 25%: Continuous operation
with intermittent loading (playing time 10 min).
Engine protection of to hot warming up:
It´s allowed to run the engine with nominal pow-
er maximum 25% of playing time. After this the
machine must run 75% of playing time steadily
without load.
Noise values
The total noise values determined in accordance
with EN 62841.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
220-240 V~ 50Hz
S1 1800W
S6 25% 2000W
5000 min
-1
ø 250 x ø 30 x 2,8 mm
24
2 mm
563 x 583 x 28 mm
85 mm
65 mm
0 - 85 mm
0 - 45°
ø 35 mm
19 kg
94,0 dB(A)
3 dB
107,0 dB(A)
3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 62841.

7. Before starting the equipment

• The equipment must be set up where it can stand
securely. Use the holes on the inner side of the
frame legs for this.
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
• Before you press the ON/OFF switch check that the
saw blade is fitted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power
supply make sure the data on the rating plate are
dentical to the mains data.
• Connect the machine to a properly installed protec-
tive contact socket, with at least 16A circuit breaker.

8. Attachment and operation

Important! Pull out the power plug before carry-
ing out any maintenance, resetting or assembly
work on the circular saw.
Place all parts supplied on a flat surface. Grouping
equal parts.
Note: If compounds with a bolt (round head / or hexa-
gon), hex nuts and washers are backed up, the wash-
er must be fitted under the nut.
Insert screws each from outside to inside. Secure
connections with nuts on the inside.
Note: Tighten the nuts and bolts during assembly
only to the extent that they can not fall down.
If you tighten the nuts and bolts prior to final assem-
bly, final assembly can not be performed.
8.1 Mounting the bench extension (fig. 5)
1. Turn the saw and place it on the floor with the
bench facing down.
2. Align the bench extension (8) flush with the saw
bench (1).
3. Push table extension (8) onto the sawing table (1)
using the hex bolts (19) and cross member (21c).
Repeat for the opposite side.
4. Screw the support struts (21a, 21b) to the table
extensions (8) with the hex bolts (19) and cross
member (21c).
5. Subsequently, tighten all screws.
GB | 31