Personal Protective Equipment - Husqvarna K 1270 II Manuel D'utilisation

Masquer les pouces Voir aussi pour K 1270 II:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Stop the product immediately if strong vibrations
suddenly occurs. Do not continue the operation
before the cause of the increased vibrations is
removed.
To cut granite or hard concrete causes more
vibration in the product than if you cut soft concrete.
Cutting equipment that is blunt, defective, of
incorrect type or incorrectly sharpened, increases
the vibration level
Exhaust fumes safety
WARNING:
instructions that follow before you use the
product.
The exhaust fumes from the engine contain carbon
monoxide which is an odourless, poisonous and very
dangerous gas. To breathe carbon monoxide can
cause death. Because carbon monoxide is odourless
and cannot be seen, it is not possible to sense it. A
symptom of carbon monoxide poisoning is dizziness,
but it is possible that a person becomes unconscious
without warning if the quantity or concentration of
carbon monoxide is sufficient.
Exhaust fumes also contain unburned hydrocarbons
including benzene. Long-term inhalation can cause
health problems.
Exhaust fumes that you can see or smell also
contain carbon monoxide.
Do not use a combustion engine product indoors or
in areas that do not have sufficient airflow.
Do not breathe the exhaust fumes.
Make sure that the airflow in the work area is
sufficient. This is very important when you operate
the product in trenches or other small work areas
where exhaust fumes can easily collect.
Dust safety
WARNING:
instructions that follow before you use the
product.
Operation of the product can cause dust in the air.
Dust can cause serious injury and permanent health
problems. Silica dust is regulated as harmful by
several authorities. These are examples of such
health problems:
The fatal lung diseases chronic bronchitis,
silicosis and pulmonary fibrosis
Cancer
Birth defects
Skin inflammation
Use correct equipment to decrease the quantity of
dust and fumes in the air and to decrease dust on
work equipment, surfaces, clothing and body parts.
Examples of controls are dust collection systems
and water sprays to bind dust. Decrease dust at the
1631 - 001 - 04.05.2021
Read the warning
Read the warning
source where possible. Make sure that the
equipment is correctly installed and used and that
regular maintenance is done.
Use approved respiratory protection. Make sure that
the respiratory protection is applicable for the
dangerous materials in the work area.
Make sure that the airflow is sufficient in the work
area.
If it is possible, point the exhaust of the product
where it cannot cause dust to go into the air.

Personal protective equipment

WARNING:
instructions that follow before you use the
product.
Always use approved personal protective equipment
during operation. Personal protective equipment
cannot eliminate the risk of injury but it will reduce
the degree of injury if an accident does happen. Ask
your servicing dealer for help in choosing the right
equipment.
Use an approved protective helmet.
Use approved hearing protection. Long-term
exposure to noise can result in permanent hearing
impairment. Be aware of warning signals or shouts
when you are wearing hearing protection. Always
remove your hearing protection as soon as the
engine stops.
Use approved eye protection to decrease the risk of
injury from thrown objects. If you use a face shield
then you must also wear approved protective
goggles. Approved protective goggles must comply
with standard ANSI Z87.1 in the USA or EN 166 in
EU countries. Visors must comply with standard EN
1731.
Use heavy duty gloves.
Use approved respiratory protection. The use of
products such as cutters, grinders, drills, that sand or
form material can generate dust and vapours which
may contain hazardous chemicals. Check the nature
of the material you intend to process and use
appropriate breathing mask.
Use tight-fitting, heavy-duty and comfortable clothing
that permits full freedom of movement. Cutting
generates sparks that can ignite clothing.
HUSQVARNA recommends that you wear flame-
retardant cotton or heavy denim. Do not wear
clothing made of material such as nylon, polyester or
rayon. If ignited such material can melt and cling to
the skin. Do not wear shorts.
Use boots with steel toe-cap and non-slip sole.
Read the warning
9

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

K 1270 ii railK 1270 smartguard

Table des Matières