To Replace The Engine Oil - Husqvarna LC 353AWD Manuel D'utilisation

Masquer les pouces Voir aussi pour LC 353AWD:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 132
6. If you do not see a leak, start the engine. Let the
engine run until the product is clean below the
housing.
7. Stop the engine.
8. Stop the water supply and remove the hose from the
water hose connection.
Note: Do not remove the water hose from the water
hose connection while the engine is in operation.
Water in the engine can decrease the life of the
engine.
9. Start the engine and let it run for a full minute to
remove remaining water from the product.

To replace the engine oil

WARNING: Engine oil is very hot directly
after the engine is stopped. Let the engine
become cool before you drain the engine oil.
If you spill engine oil on your skin, clean with
soap and water.
1. Operate the product until the fuel tank is empty.
2. Remove the ignition cable from the spark plug.
3. Remove the oil tank cap.
4. Put a container below the product to collect the
engine oil in.
5. Tilt the product to drain the engine oil from the oil
tank.
6. Fill with new engine oil of the type recommended in
Technical data on page 19 .
7. Do a check of the oil level. Refer to
the oil level on page 11 .
To examine the spark plug
CAUTION: Always use the recommended
spark plug type. Incorrect spark plug type
can cause damage to the product.
Examine the spark plug if the engine is low on
power, is not easy to start or does not operate
correctly at idle speed.
To decrease the risk of unwanted material on the
spark plug electrodes, obey these instructions:
a) Make sure that the idle speed is correctly
adjusted.
b) Make sure that the fuel mixture is correct.
c) Make sure that the air filter is clean.
If the spark plug is dirty, clean it and make sure that
the electrode gap is correct, refer to
on page 19 . (Fig. 41)
Replace the spark plug if it is necessary.
To clean the air filter
1. Remove the air filter cover and remove the filter.
1242 - 003 - 01.11.2019
2. Hit the filter against a flat surface to make the
3. Put the air filter back. Make sure that the air filter
4. Put the air filter cover back.
Note: An air filter that is used for a long time cannot be
fully cleaned. Replace the air filter at regular intervals.
Always replace a damaged air filter.
To examine the cutting equipment
1. Examine the cutting equipment for damage or
2. Look at the blade to see if it is damaged or blunt.
Note: It is necessary to balance the blade after it is
sharpened. Let a service center sharpen, replace and
To do a check of
balance the blade. If you hit an obstacle that causes the
product to stop, replace the damaged blade. Let the
service center estimate if the blade can be sharpened or
must be replaced.
To assemble the blade
1. Put the blade adapter on the engine crankshaft.
2. Always attach the blade with the angled ends
3. Use a block of wood between the blade and product
4. Always tighten the bolt with a torque of 35-40 ft lbs
Technical data
5. Make sure the spark plug cable is disconnected from
particles fall off.
CAUTION: Do not use solvent or
compressed air to clean the air filter.
fully seals against the air filter holder.
WARNING: To prevent accidental start
remove the ignition cable from the spark
plug.
WARNING: Use protective gloves when you
do maintenance on the cutting equipment.
The blade is very sharp and cuts can easily
occur.
cracks. Always replace a damaged cutting
equipment.
Make sure the key in the adapter and crankshaft
keyway are aligned.
(Fig. 42)
pointing up in the direction of the engine.
(Fig. 43)
housing. Tighten the blade bolt and turn it clockwise.
(47-54 Nm).
(Fig. 44)
the engine.
CAUTION: To prevent accidental start,
always disconnect the spark plug cable
15

Publicité

Table des Matières
loading

Table des Matières