Extension Cords - Milwaukee 0233-20 Manuel De L'utilisateur

GROUNDING
WARNING
Improperly connecting the
grounding wire can result in the risk of elec-
tric shock. Check with a qualifi ed electrician
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug
provided with the tool. Never remove the
grounding prong from the plug. Do not use
the tool if the cord or plug is damaged. If
damaged, have it repaired by a MILWAUKEE
service facility before use. If the plug will not
fi t the outlet, have a proper outlet installed by
a qualifi ed electrician.
Grounded Tools:
Tools with Three Prong Plugs
Tools marked "Grounding Required" have a three
wire cord and three prong grounding plug. The
plug must be connected to a properly grounded
outlet (See Figure A). If the tool should electrically
malfunction or break down, grounding provides a
low resistance path to carry electricity away from
the user, reducing the risk of electric shock.
The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire in the
cord must be the only wire connected to the tool's
grounding system and must never be attached to
an electrically "live" terminal.
Your tool must be plugged into an appropriate out-
let, properly installed and grounded in accordance
with all codes and ordinances.
The plug and outlet should
look like those in Figure A.
Fig. A
Double Insulated Tools:
Tools with Two Prong Plugs
Tools marked "Double Insulated" do not require
grounding. They have a special double insula-
tion system which satisfi es OSHA requirements
and complies with the applicable standards of
Underwriters Laboratories,
Inc., the Canadian Stan-
dard Association and the
National Electrical Code.
Double Insulated tools may
be used in either of the
120 volt outlets shown in
Figures B and C.
Fig. B Fig. C

EXTENSION CORDS

Grounded tools require a three wire extension
cord. Double insulated tools can use either a two
or three wire extension cord. As the distance from
the supply outlet increases, you must use a heavier
gauge extension cord. Using extension cords with
inadequately sized wire causes a serious drop in
voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the
required minimum wire size.
The smaller the gauge number of the wire, the
greater the capacity of the cord. For example, a 14
gauge cord can carry a higher current than a 16
gauge cord. When using more than one extension
cord to make up the total length, be sure each cord
contains at least the minimum wire size required. If
you are using one extension cord for more than one
tool, add the nameplate amperes and use the sum
to determine the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors,
be sure it is marked with the suffi x "W-A" ("W"
in Canada) to indicate that it is acceptable for
outdoor use.
• Be sure your extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired by
a qualifi ed person before using it.
• Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Recommended Minimum Wire Gauge
for Extension Cords*
Extension Cord Length
Nameplate
Amperes 75'
25' 50' 100'
0 - 2.0 18 18 18 18
2.1 - 3.4 18 18 18 16
3.5 - 5.0 18 18 16 14
14
5.1 - 7.0 18 16 12
7.1 - 12.0 16 14 12 10
12.1 - 16.0 14 12 10
16.1 - 20.0 12 10
* Based on limiting the line voltage drop to
fi ve volts at 150% of the rated amperes.
READ AND SAVE ALL
INSTRUCTIONS FOR
FUTURE USE.
4
WARNING
To reduce the risk of injury,
always unplug tool before attaching or remov-
ing accessories or making adjustments. Use
only specifi cally recommended accessories.
Others may be hazardous.
Removing and Replacing Quik-Lok
MILWAUKEE's exclusive Quik-Lok
instant fi eld replacement or substitution.
Fig. 1
1 2
1. To remove the Quik-Lok
1/4 turn to the left and pull it out.
2. To replace the Quik-Lok
nector keyways and push the connector in as
far as it will go. Turn the cord nut 1/4 turn to the
150'
right to lock.
16
14
Installing Side Handle
12
MILWAUKEE Magnum Drills are supplied with a
12 side handle that can be installed on either side of
the tool for right or left handed use. To install the
side handle, thread it into the socket on the desired
side of the tool and tighten it securely. Always use
the side handle for best control.
Specifi cations
Cat. No. Volts AC Amps No Load RPM
0233-20 120 5.5 0-2800
0234-6 120 5.5 without RAD 0-950
RAD low 0-630
RAD high 0-1425
0235-21 120 5.5 0-950
0244-1 120 5.5 without RAD 0-700
RAD low 0-465
RAD high 0-1050
Right Angle Drive Unit Cat. No. 48-06-2871
ASSEMBLY
WARNING
always remove the chuck key from the chuck
after each use.
Installing Bits into Keyed Chucks
(Cat. No. 0234-6, 0244-1)
® Cords Always unplug the tool before installing or remov-
ing bits.
®
Cords provide
1. Open the chuck jaws wide enough to insert the bit.
Be sure the bit shank and chuck jaws are clean.
Dirt particles may prevent the bit from lining up
properly.
3 4
2. When using drill bits, insert the bit into the chuck.
Center the bit in the chuck jaws and lift it about
1/16" off of the bottom. Tighten the chuck jaws
by hand to align the bit.
®
Cord, turn the cord nut
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the bit shank.
®
Cord, align the con-
Tighten the chuck jaws by hand to align the bit.
3. Place the chuck key in each of the three holes in
the chuck, turning it clockwise as shown. Tighten
securely.
Fig. 2
Tighten
4. To remove the bit, insert the chuck key into one
of the holes in the chuck and turn it counterclock-
wise.
5
To prevent personal injury,
Loosen