Noise/Vibration Information; Declaration Of Conformity - Bosch GSA 1200 E Professional Notice Originale

OBJ_BUCH-69-002.book Page 17 Thursday, December 13, 2007 3:25 PM

Noise/Vibration Information

Measured values determined according to
EN 60745.
Typically the A-weighted noise levels of the
product are: Sound pressure level 89 dB(A);
Sound power level 100 dB(A). Uncertainty
K =1.5 dB.
Wear hearing protection!
Vibration total values (triax vector sum) deter-
mined according to EN 60745:
Cutting wood: Vibration emission value
2
a =19 m/s , Uncertainty K=5.5 m/s
h
The vibration emission level given in this infor-
mation sheet has been measured in accordance
with a standardised test given in EN 60745 and
may be used to compare one tool with another.
It may be used for a preliminary assessment of
exposure.
The declared vibration emission level repre-
sents the main applications of the tool. However
if the tool is used for different applications, with
different accessories or poorly maintained, the
vibration emission may differ. This may signifi-
cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibra-
tion should also take into account the times
when the tool is switched off or when it is run-
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the to-
tal working period.
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.

Declaration of Conformity

We declare under our sole responsibility that
the product described under "Technical Data" is
in conformity with the following standards or
standardization documents: EN 60745 accord-
ing to the provisions of the directives
2004/108/EC, 98/37/EC (until Dec. 28, 2009),
2006/42/EC (from Dec. 29, 2009 on).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Bosch Power Tools
Dr. Egbert Schneider
Senior Vice President
Engineering
21.11.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Assembly
2
.
Replacing/Inserting the Saw Blade
Before any work on the machine itself, pull
the mains plug.
When mounting the saw blade, wear protec-
tive gloves. Danger of injury when touching
the saw blade.
When changing the saw blade, take care
that the saw blade holder is free of material
residue, e. g. wood or metal shavings.
Selecting a Saw Blade
An overview of recommended saw blades can
be found at the beginning of these operating in-
structions. Use only saw blades with single-nose
shank. The saw blade should not be longer than
required for the intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A)
Press the saw blade 1 firmly into the saw blade
holder 3 until it can clearly be heard to engage.
This causes the locking sleeve 4 to turn by ap-
prox. 90° and locks the saw blade.
If the saw blade 1 is not locked, turn the locking
sleeve 4 approx. 90° in the direction of the ar-
row until it locks in the open position and a
"click" can be heard. Then press the saw blade
1 into the saw blade holder 3 again.
Check the tight seating of the saw blade. A
loose saw blade can fall out and lead to inju-
ries.
For certain work, the saw blade 1 can also be
turned through 180° (with the teeth pointed up-
wards) and re-inserted again.
English | 17
Dr. Eckerhard Strötgen
Head of Product
Certification
1 609 929 K93 | (13.12.07)