Ordering Replacement Parts; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL GE-SA 1335 P Instructions D'origine

•
Assemble in reverse order
Warning! Never clean the air fi lter with petrol or
infl ammable solvents.
Servicing/Replacing the spark plug
Check the spark plug for dirt and grime after 10
hours of operation and if necessary clean it with
a copper wire brush. Thereafter service the spark
plug after every 50 hours of operation.
•
Pull off the spark plug boot (Fig. 12a) with a
twist.
•
Remove the spark plug using a spark plug
wrench (Fig. 12b).
•
Assemble in reverse order.
Changing the roller (see Fig. 11a-11d)
Be sure to wear work gloves!
Only replace the roller with a genuine Einhell rol-
ler, as this will ensure top performance and safety
under all conditions.
Remove the two Allen screws (Fig. 11a / Item
A). Lift the roller on this side and pull out in the
direction of the arrow (Fig. 11b). Slide the new
roller in the direction of the arrow (Fig. 11d) onto
the square-ended drive (Fig. 11c/ Item A) and
press into the holder (Fig. 11d). Use the two Al-
len screws (Fig. 11a /Item A) to secure the roller
again.
Apply grease to the square-ended drive from time
to time so that the rollers can be changed easily.
If the cutting unit is set unfavorably, the outer
blade (Fig. 11b/Item A) may be blocked by the
housing. In this case move the roller half a turn
forward!
7.3 Preparing the equipment for storage
Danger! Do not empty the petrol tank in enclosed
areas, near fi re or when smoking. Petrol fumes
can cause explosions and fi re.
1. Empty the petrol tank with a petrol suction
pump.
2. Start the engine and let it run until any remai-
ning petrol has been used up.
3. Change the oil at the end of every season.
To do so, remove the used engine oil from a
warm engine and refi ll with fresh oil.
4. Remove the spark plug from the cylinder
head. Fill the cylinder with approx. 20 ml of oil
from an oil can. Slowly pull back the starter
handle, which will bathe the cylinder wall with
oil. Screw the spark plug back in.
5. Clean the cooling fi ns of the cylinder and the
housing.
Anl_GE_SA_1335_P_SPK7.indb 25 Anl_GE_SA_1335_P_SPK7.indb 25
GB
6. Be sure to clean the entire machine to protect
the paint.
7. Store the machine in a well-ventilated place.
8. The push bar has a P position (Fig. 6) in or-
der to take up less space during storage. To
adopt this position you must loosen the quick-
release levers by approx. 3 turns to allow for
the higher fastening in the parking position.
With the bar in this position, the scarifi er can
be stood in a corner in minimum space (Fig.
10). When you return the bar to the working
position, remember to tighten the quick-
release levers again by 3 turns!
7.4 Preparing the device for transport
1. Drain the petrol tank using a petrol extraction
pump.
2. Always let the engine run until it has used up
the remainder of petrol in the tank.
3. Empty the engine oil from the warm engine.
4. Remove the spark plug boot from the spark
plug.
5. Clean the cooling fi ns of the cylinder and the
housing.
6. Remove the push bars if necessary.

7.5 Ordering replacement parts

Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
8. Cleaning, maintenance and
ordering of spare parts
The unit is supplied in packaging to prevent its
being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic. De-
fective components must be disposed of as spe-
cial waste. Ask your dealer or your local council.
- 25 -
18.08.2015 09:43:15 18.08.2015 09:43:15