Specified Conditions Of Use - Milwaukee M18 HUP700 Notice Originale

Only use devices, battery packs and chargers that are in perfect
technical condition.
Have damage repaired immediately by an authorised workshop.
To avoid injury and damage, prevent accidental starting of the
device.
Remove any setting tools and wrenches before the operation.
Do not work on electrically live parts. Device is NOT insulated.
Keep hands and loose items of clothing away from cutting tools and
other moving parts.
In the event of problems during the crimping process, immediately
release the ON switch and press the unlocking button on the
hydraulic system. The valve will open and the piston will return to
its initial position.
WARNING! To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your device, battery
pack or charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., Can
cause a short circuit.
Compliance with the specified service work and service intervals is
GB
mandatory.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Use only System M18 chargers for charging System M18 battery
packs. Do not use battery packs from other systems.
To avoid injury and damage, never immerse the tool, removable
battery or charger in liquid or allow liquid to penetrate them.
WARNING
This device contains a button-type/coin cell lithium battery.
A new or used battery can cause severe internal burns and
lead to death in as little as 2 hours if swallowed or if it enters the
body. Always secure the cover on the battery compartment. If it
does not close securely, stop the device, remove the battery and
keep it out of reach of children. If you believe that someone has
swallowed the battery or that it has otherwise entered the body,
seek immediate medical attention.
CRIMPING TOOL SAFETY WARNINGS
Crimping tools and crimping devices must only be used by trained
personnel in electrotechnical applications.
Never crimp live connecting materials.
Check crimping tool, jaws and dies for cracks and other signs of
wear before each use.
Only use crimping tools and crimping dies that are in perfect
technical condition.
Only use the crimping tool with crimping dies inserted into it.
Do not touch the press jaws and the press bolt during the pressing
operation.
In the event of problems during the crimping process, immediately
release the ON switch and press the unlocking button on the
hydraulic system. The valve will open and the piston will return to
its initial position.
CABLE CUTTER SAFETY WARNINGS
Only personnel trained in electrotechnical applications may carry
out cutting and splitting of cables and cords with the aid of this
cable cutter.
To reduce the risk of explosions, electric shock and damage to
property and equipment, never cut live electrical cables. Device is
NOT insulated.
English
Deutsch
26 26
Keep hands and loose items of clothing away from cutting tools
and other moving parts. There is a risk of serious injury, including
severing of limbs.
Before the cutting process begins, access must be sealed off in
accordance with local regulations.
Only ever cut cables that have been disconnected from the power
supply!
Cable and cord may not be exposed to any mechanical forces.
To reduce the risk of injury, wear safety goggles or glasses with
side shields.
Failure to comply with this instruction can lead to serious injury,
death, fire and other damage to property as a result of electric
shock, explosion and/or electric arcs.
Never hold the cable cutter by the cutting jaws.
Before using, always check the cutting jaws for cracks and other
signs of wear.
The cable cutter may only be used with a cutting tool inserted.
KNOCKOUT TOOL SAFETY WARNINGS
Check the cutting tool for cracks or any other signs of wear before
using. Only use cutting tools and cutting devices if they are in
perfect technical condition.
Only operate the device with the cutting tool inserted into it. Do
not use in or near live electrical panels. Only work on de-energized
electrical panels.
Check whether the nominal width of the die corresponds to the
nominal width of the punch.
Use tool only with knockout dies and punches rated for the peak
output force of this tool. Any other use may cause injuries or
damage to the tool.
Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to get jammed and are
easier to control.

SPECIFIED CONDITIONS OF USE

Accessories and Tool heads:
Intended use: only for single acting accessories and tool heads,
nominal pressure 700 bar; max. oil displacement 1,35l
Crimping Tool:
The crimping tool is exclusively designed for crimping connectors
and compound materials with dedicated crimping dies.
All live parts, i.e., parts conducting electricity, must be discon-
nected in the technician's work environment prior to starting work.
Cable Cutter:
The cable cutter is suitable for cutting:
• tension-free non-reinforced cables of insulated copper or
aluminum, cutting tools depending on cable type
Knockout tool:
The Knockout tool may only be used for punching in Materials with
the provided stamps and matrices.
WARNING Read all safety warnings, instructions, illus-
trations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.