Technical Data; Scope Of Supply - REMS SSM 160 RS Notice D'utilisation

eng
● Keep the heating element butt welding unit (5) away from inflammable
materials. A fire could be caused.
● Keep the connecting cable away from the hot heating element butt welding
unit (5). There is a risk of injury by electric shock.
● Do not reach into the rotating blade of the facing cutter (6). There is a risk
of injury.
● Do not overload the facing cutter (6) by too high thrust pressure. This will
damage the facing cutter.
● Only connect the power tool to an outlet with a functioning protected earth.
● Only use approved and appropriately marked extension leads with a suffi-
cient cable cross-section. Use extension leads up to a length of 10 m with
cable cross­section 1.5 mm², from 10 – 30 m with cable cross­section 2.5 mm².
● Check the connecting cables of the power tool and extension leads regularly
for damage. Have these renewed by qualified experts or an authorised REMS
customer service workshop in case of damage.
● Only allow trained persons to use the power tool. Apprentices may only use
the power tool when they are over 16, when this is necessary for their training
and when they are supervised by a trained operative.
● Children and persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the power tool
1. Technical data
Use for the intended purpose
WARNING
Use REMS SSM heating element butt welding machines for welding plastic pipes and mouldings of PB, PE, PP and PVDF.
All other uses are not for the intended purpose and are therefore prohibited.
1.1. Scope of Supply
REMS SSM 160 RS: Heating element butt welding machine, heating element butt welding unit, protective cover for heating element, facing cutter, 2 vices with 2
clamp inserts each Ø 40, 50, 56, 63, 75, 90, 110, 125, 135, 140, 160 mm. 2 pipe rests Ø 160 mm with pipe rest inserts Ø 40, 50, 56, 63, 75, 90,
110, 125, 135, 140 mm. Work key. Steel case, pipe rack, operating instructions.
REMS SSM 160 KS: Heating element butt welding machine, heating element butt welding unit, protective cover for heating element, facing cutter, 2 vices with 2
clamp inserts each Ø 40, 50, 56, 63, 75, 90, 110, 125, 135, 140, 160 mm. 2 pipe rests Ø 160 mm with pipe rest inserts Ø 40, 50, 56, 63, 75, 90,
110, 125, 135, 140 mm. Operating key, sheet steel base with installed drawer, closed sheet steel underframe, operating instructions.
REMS SSM 250 KS: Heating element butt welding machine, heating element butt welding unit, facing cutter, quick clamping device with 2 clamping jaws and 2 clamp
inserts each Ø 75, 90,110, 125, 160, 200 mm. 2 pipe rests with pipe rest inserts Ø 75, 90, 110, 125, 160, 200, 250 mm. Sheet steel base with
installed drawer, operating key, closed sheet steel underframe, operating instructions.
REMS SSM 315 RF: Heating element butt welding machine, heating element butt welding unit, facing cutter, quick clamping device with 2 clamping jaws and 2 clamp
inserts each Ø 90, 110, 125, 160, 200, 250 mm. 2 pipe rests with pipe rest inserts Ø 90, 110, 125, 160, 200, 250 mm. Sheet steel base with
installed drawer, operating key, closed sheet steel underframe, operating instructions.
1.2. Article numbers
Heating element – butt welding machine with
Heating element – butt welding unit EE
(adjustable temperature, electronic regulation)
Heating element – butt welding machine with
Heating element – butt welding unit EE
(adjustable temperature, electronic regulation)
With clamping devices for angular branches
Heating element – butt welding unit EE
(adjustable temperature, electronic regulation)
Supporting stand MSG, SSG 110 –180
Supporting stand SSG 280
Bench support MSG, SSG 110 –180
Bench support SSG 280
Protection cover
Facing cutter blade
Clamp right
Clamp left
Clamp insert set Dm 40
Clamp insert set Dm 50
Clamp insert set Dm 56
Clamp insert set Dm 63
Clamp insert set Dm 75
Clamp insert set Dm 90
Clamp insert set Dm 110
Clamp insert set Dm 125
Clamp insert set Dm 135
Clamp insert set Dm 140
Clamp insert set Dm 160
Clamp insert set Dm 180
Clamp insert set Dm 200
Clamp insert set Dm 225
Clamp insert set Dm 250
Clamp insert set Dm 280
Pipe support right/left
Pipe support insert set Dm 40
Pipe support insert set Dm 50
Pipe support insert set Dm 56
Pipe support insert set Dm 63
Pipe support insert set Dm 75
Pipe support insert set Dm 90
Explanation of symbols
NOTICE
SSM 160 RS
252026
250220
250040
250041
250243
252103
252500
252501
252502
252503
252504
252505
252506
252507
252508
252509
252510
252511
252512
252350
252370
252371
252372
252373
252374
252375
safely may not use this power tool without supervision or instruction by a
responsible person. Otherwise there is a risk of operating errors and injuries.
WARNING
Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Power tool complies with protection class I
Environmentally friendly disposal
CE conformity mark
SSM 160 KS SSM 250 KS
252046 254025
250220 250330
250040
250340
250041
250341
250243 250343
252103 254103
252500 254300
252501 254310
252502
252503
252504
252505
252506 254320
252507 254321
252508 254322
252509 254323
252510
252511 254324
252512 254325
254326
254327
254328
252350 254350
252370
252371
252372
252373
252374 254370
252375 254371
eng
SSM 315 RF
255020
250420
255103
255300
255310
255320
255321
255322
255323
255324
255325
255326
255327
255328
255329
255350
254371
13