Product Description; Designations Of The Components Shown (Figure A - C); Technical Data; Assembly/Installation - ABNOX AXSP-S Instructions De Service

EN
• Deficient monitoring of the machine parts that are
subject to wear.
• Improperly completed repairs or use of third-party
components.

Product Description

Intended Use
The lubricant pump is ideal as a feed pump for
ABNOX dosing valves or as a transfer pumping and
decanting system.
ABNOX compressed air grease pumps are used to
pump medium to high-viscosity lubricants as well as
silicone greases and oils.
Labelling
The AXSP lubricant pump is marked on the motor
and on the suction system. See the following table for
a detailed explanation of the information:
Product family Air motor ø Suction system
AXSP SXXX
18
Designations of the components
shown (Figure A – C)
1. Suction valve
2. Suction system
3. Mounting thread
4. Material discharge
5. Air bleed connection (optional)
6. Coupling screws
7. Coupling disc
8. Air motor
9. Compressed air connection
10. Air bleed valve (optional)
11. Rotary knob (open/close)
12. Air bleed valve output
13. Mounting thread
14. Positioning screws
Suction pipe length
DXX LXXXX

Technical Data

Model
Pressure ratio
Output pressure (medium) at 6 bar working
pressure (bar)
Flow rate at pump discharge (cm
Conveying volume per double stroke (cm
Min. / Max. inlet operating pressure (bar)
Max. air consumption (l/min.)
Suction pipe diameter (mm)
Connection (compressed air) inside thread
Connection (medium) outside thread
Medium specification
Min./max. temperature (°C)
Noise emissions (decibels)
Weight (kg)
Options
XXX

Assembly/Installation

The product is to be set up or installed at the inten-
ded use site under due consideration of the following
conditions:
• At the location and site all applicable provisions of
law must be clarified and compliance with them
assured.
• The ground and space relations are to be clarified
prior to set-up/installation of the product in order
to assure safe operation for the personnel and the
product long-term. The product must be set-up/
installed so that safe, permanent operation is
assured.
• The product may only be set up and commissioned
by specially trained technicians.
• The product is constructed for rooms that are
protected from the influence of the weather
(industry standard).
• The operation and storage in aggressive or humid
environments or outdoors can lead to corrosion
damages.
AXSP
25:1
150
/min) 1500
3
/min) 31
3
2 / 10
G1/4"
G1/4"
Lubricants up to NLGI 3/5,000 m Pa.s
10 / 40
59 - 64

Coupling the air motor/suction system

1. Couple the piston rod of the air motor to the piston
rod of the suction system (Figure B)
2. Align the three positioning screws
(Figure B/No. 14)
3. Slide the air motor and suction system together
until the heads of the positioning screws are pres-
sed through the coupling discs against the stop of
the air motor (Figure C)
4. Secure with the coupling disc (Figure C/No. 7)
5. Firmly tighten the two coupling screws (Figure C)

Commissioning

• Set the feed pump into an appropriate original
container with corresponding follower plate.
• Connect the feed pump to the compressed air
supply (Figure A/No. 9). ATTENTION: The pump
starts immediately after it is connected to the
compressed air supply.
• Bleed the feed pump until grease comes out
continuously:
- Figure A/No.10 (optional)
- Figure A/No. 4
• Turn off the feed pump  disconnect or turn off the
compressed air supply (Figure A/No. 9).
60:1
360
700
13
2 / 10
200
32
2.75
19