Preparing For Operation - Bosch GCM 12 GDL Professional Notice Originale

Removing the Saw Blade
– Bring the power tool into the work position.
– Unscrew the locking screw (42) by hand until the linkage
(43) can hang down freely.
– Loosen the fastening screw (44) (by approx. two turns)
using the hex key (4 mm) (17).
Do not unscrew the screw completely.
– Loosen the fastening screw (45) (by approx. six turns)
using the hex key (4 mm) (17).
Do not unscrew the screw completely.
– Pull the cover plate (46) forwards and downwards away
from the fastening screw (45).
– Swivel the retracting blade guard (4) to the back and hold
the retracting blade guard in this position.
– Hang the linkage (43) over the fastening screw (45) using
a hole.
This will hold the retracting blade guard open.
– Turn the hex socket screw (48) with the hex key (6 mm)
(17) and at the same time press the spindle lock (47) un-
til it engages.
– Press and hold the spindle lock (47) and loosen the hex
socket screw (48) by turning it clockwise (left-hand
thread).
– Remove the clamping flange (49).
– Remove the saw blade (40).
Fitting the saw blade
If required, clean all the parts you want to fit before installing
them.
– Place the new saw blade onto the interior clamping flange
(50).
When fitting the saw blade, make sure that the cutting
u
direction of the teeth (arrow direction on the saw
blade) matches the direction of the arrow on the pro-
tective guard.
– Fit the clamping flange (49) and the hex socket screw
(48). Press the spindle lock (47) until it engages and
tighten the hex socket screw by turning it anticlockwise.
– Release the linkage (43) from the fastening screw (45)
and guide the retracting blade guard (4) back down.
– Slide the cover plate (46) back under the fastening screw
(45).
– Retighten the fastening screws (45) and (44).
– Slide the linkage (43) into its original position and
retighten the locking screw (42) by hand.
Operation
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Transport Safety Lock (see figure A)
The transport safety lock (31) makes it easier to handle the
power tool when transporting it to various working locations.
Bosch Power Tools
Unlocking the Power Tool (Work Position)
– Press the glide arm (28) down slightly by the handle (1)
to release the transport safety lock (31).
– Pull the transport safety lock (31) all the way out.
– Slowly guide the glide arm (28) upwards.
Locking the Power Tool (Transport Position)
– Slide the glide arm (28) all the way back and secure it in
this position (see "Securing the Glide Arm (see figure
B2)", page 37).
– Guide the glide arm downwards until you can press the
transport safety lock (31) all the way in.
Further information: (see "Transport (see figure Z)",
page 43)
Locking the Glide Arm
The glide mechanism of the glide arm (28) can be locked
with the clamping lever (25). The glide arm can be placed in
two positions:
– Glide arm pushed all the way back (for cross cuts)
– Glide arm pulled all the way forward (for a compact trans-
port position)
Unlocking the Glide Arm (see figure B1)
After unlocking the glide arm (28), the whole gliding mech-
anism is ready for operation.
– Press the clamping lever (25) all the way down.
– The clamping wedge of the clamping lever releases the
two articulated parts at the bottom of the glide arm.
Securing the Glide Arm (see figure B2)
Glide arm pushed all the way back:
– Push the glide arm (28) all the way back.
– The two articulated parts at the top of the glide arm are
now upright and closed.
– Pull the clamping lever (25) upwards until the clamping
wedge is positioned between the two articulated parts at
the bottom of the glide arm.
– This locks the glide arm (28), which is pushed all the way
back.
Glide arm pulled all the way forward:
– Pull the glide arm (28) all the way forward.
– The glide mechanism is now completely extended.
– Pull the clamping lever (25) upwards until the clamping
wedge is positioned between the two articulated parts at
the bottom of the glide arm.
– This locks the glide arm (28), which is pulled all the way
forward.

Preparing for Operation

Extending the Saw Table (see figure C)
The free end of long workpieces must have something
placed underneath it or be supported.
The saw table can be extended left and right using the saw
table extensions (7).
– Push the clamping lever (51) inwards.
English | 37
1 609 92A 4CT | (20.07.2018)