Functional Description - Milwaukee M18 Fuel Manuel De L'utilisateur

• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, flush with water. If liquid con-
tacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is dam-
aged or modified. Damaged or modified batteries
may exhibit unpredictable behavior resulting in
explosion or risk of injury.
• Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instructions.
Charging improperly or at temperatures outside
the specified range may damage the battery and
increase the risk of fire.
SERVICE
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
IMPACT WRENCHES
• Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting
a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
• Wear ear protectors when impact drilling. Expo-
sure to noise can cause hearing loss.
• Use only sockets and other accessories spe-
cifically designed for use on impact wrenches
and drivers. Other sockets and accessories might
shatter or break causing injury.
• For best results, use only with energy absorbing
lanyards. Ropes, straps or chains may break
and cause failure. Do not use with lanyards at
full tension.
• To reduce the risk of injury in ap-
WARNING
plications that produce a consid-
erable amount of dust, use an OSHA compliant
dust extraction solution in accordance with the
solution's operating instructions.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service
replacement.
• Some dust created by power sand-
WARNING
ing, sawing, grinding, drilling, and
other construction activities contains chemicals
known to cause cancer, birth defects or other repro-
ductive harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are spe-
cially designed to filter out microscopic particles.
fire,
Cat. No. ..................................................... 2867-20
Volts .............................................................. 18 DC
Battery Type .................................................M18™
Charger
Anvil Type ....................................... 1" Square-Ring
RPM ...................Mode 1...................Speed 0-1000
IPM ....................Mode 1 ................Impacts 0-1330
Recommended Ambient
1. Side handle
2. Tool hanger ring
3. Tool hanger
4. Control switch
facility for a free 5. Handle
6. Drive control (not shown)
7. ONE-KEY™ coin battery door
8. LED
9. Trigger
10. Square drive anvil with friction ring
3
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
Impacts per Minute Under Load (IPM)
UL Listing for
US Canada and U.S.
C
SPECIFICATIONS
Type ................................................M18™
Mode 2................... Speed 0-1100
Mode 3...................Speed 0-1400
Mode 4...................Speed 0-1650
Mode 2.................Impacts 0-1620
Mode 3.................Impacts 0-2100
Mode 4.................Impacts 0-2450
Operating Temperature ......................0°F to 125°F

FUNCTIONAL DESCRIPTION

1
10
9
8
2
3
4
5
6
7