User Manual; Ignition; Controlling The Temperature; Switching Off - Dru Verwarming PIGALLE-01 Instructions D'installation Et Mode D'emploi

USER MANUAL

Ignition

USER INSTRUCTIONS
Ignition button A has three positions, i.e.:
O position
Pilot burner position
USER MANUAL
Full position
Ignition
Turn the ignition button to the left from position O,
Ignition button A has three positions, i.e.:
press down firmly as well and keep turning to the
pilot burner position . By turning the button, the
O position
pilot burner is ignited by means of an electrical
Pilot burner position
spark. When the pilot burner burns, keep pressing
Full position
down the button for approx. 10 sec. and then let
go. The pilot burner is visible from the side, behind
Turn the ignition button to the left from position O,
the glass window. If the pilot burner does not
press down firmly as well and keep turning to the pilot
ignite at once, the above-mentioned action can be
burner position . By turning the button, the pilot burner
repeated immediately by turning the pressed down
is ignited by means of an electrical spark. When the pilot
button back towards O and then left again towards
burner burns, keep pressing down the button for approx.
the pilot burner position. After letting go of the
10 sec. and then let go. The pilot burner is visible from
ignition button, the pilot burner should continue to
the side, behind the glass window. If the pilot burner
burn. Then turn the ignition button further
does not ignite at once, the above-mentioned action can
towards the full position . Depending on
be repeated immediately by turning the pressed down
thermostat button B, the main burner will be
button back towards O and then left again towards the
pilot burner position. After letting go of the ignition
ignited.
button, the pilot burner should continue to burn. Then
turn the ignition button further towards the full position

Controlling the temperature

. Depending on thermostat button B, the main burner will
The position of thermostat button B determines
be ignited.
the temperature in the room. Position 6 provides
the highest temperature, position 1 the lowest.
Controlling the temperature
The thermostat controls the burner by modulating
The position of thermostat button B determines the
between "full position" and "low position" of the
temperature in the room. Position 6 provides the highest
burner. The thermostat will automatically keep the
temperature, position 1 the lowest. The thermostat
room at the required set temperature.
controls the burner by modulating between "full position"
and "low position" of the burner. The thermostat will

Switching off

automatically keep the room at the required set
Turn ignition button A back to the Pilot Burner
temperature.
position ( symbol), only the pilot burner will
continue to burn. In order to switch off the
Switching off
appliance fully, you must press down button A and
Turn ignition button A back to the Pilot Burner position
turn it back to position O.
( symbol), only the pilot burner will continue to burn.
In order to switch off the appliance fully, you must press

Important

down button A and turn it back to position O.
An incorporated safety lock will be activated if the
appliance is set to the ,,OFF" (O) position.
Important
Therefore, wait 5 minutes before re-igniting the
An incorporated safety lock will be activated if the
appliance. Do not try to press down the ignition
appliance is set to the ,,OFF" (O) position. Therefore, wait
button during this time, as it is locked by means of
5 minutes before re-igniting the appliance. Do not try
the safety lock. Do not force the button, because
to press down the ignition button during this time, as it is
the mechanism could get damaged.
locked by means of the safety lock. Do not force the
button, because the mechanism could get damaged.

Eco control pack

Eco control pack
It is possible to order a separately available "Eco
It is possible to order a separately available "Eco control
control pack" with remote control. The "Eco
pack" with remote control. The "Eco control pack" is
needed to get the best out of your appliance.
button points to O
button points to
button points to
button points to O
button points to
button points to
control pack" is needed to get the best out of your
appliance.
This set has a receiver that must be placed in the
tray specifically intended for this purpose.
Art 2-01: The tray is located on the left side of the
This set has a receiver that must be placed in the tray
gas control.
specifically intended for this purpose.
Art 3-01, 4-01, 5-01, 6-01, 8-02, 10-02: The tray is
The tray is located under the gas control and can be
located under the gas control.
reached by removing the cover.
Prevent cables from making contact with hot
Prevent cables from making contact with hot internal
internal components.
components.
N.B.: If the flue spillage sensor is repeatedly
activated, a qualified gas installer should be
contacted.
16
B
A
38P-0744/0