Sst1 Menu Control - AKG IVM1 Mode D'emploi

7.5. SST1 Menu Control

In the diagrams below, keys to be pressed are shown as
unpressed keys as O.
Blinking display messages appear between > and <.
Pressing the or key once decreases or increases the asso-
ciated value by one step.
7.5.1. Switch-on Menu (Main Menu)
On connecting the SST1 to power, the display will show the install-
ed software version for about 5 seconds and then change to the
main menu with the settings active at the time the SST1 was last
disconnected from power. It might look like this:
Custom Tight
4 A b
█ █
EAR SND AMB STEREO RFCH
IVA
7.5.2. Stereo/Mono
Depending on whether you connected a mono or stereo source,
you need to switch the transmitter to mono or stereo mode:
1. Press MENU.
2. Press or as many times as necessary to call up this dis-
play:
Menu: Stereo
4 A b
█ █
EAR SND AMB STEREO RFCH
IVA
3. Press SELECT. The message >STEREO< will be blinking in the
display:
Stereo: >STEREO<
4 A b
█ █
EAR SND AMB STEREO RFCH
IVA
4. To enter mono mode, press
to >MONO<.
5. Having selected the desired setting, press SELECT.
The display will revert to the main menu.
If you selected "STEREO", a solid rectangle will appear in the
display above the "STEREO" label:
Custom Tight
4 A b
█ █
EAR SND AMB STEREO RFCH
IVA
If you selected "MONO", there will be no solid rectangle
above the "STEREO" label:
Custom Tight
4 A b
█
EAR SND AMB STEREO RFCH
IVA
O O
04
LOCK
O O
MENU SELECT
04
O
LOCK
MENU SELECT
O O
04
O
LOCK
MENU SELECT
or . The display will change
O O
04
O
LOCK
MENU SELECT
O O
04
O
LOCK
MENU SELECT
7.5.3. Sound
, Selecting Sounds in Normal Mode
Eight different preset "Sounds" are stored in the transmitter's
memory. Sounds A through C (Custom Tight, Medium, and Open)
have been created specifically to match the supplied IP1 in-ear
phones from AKG. Sounds D, E, and F (Mold Tight, Medium, and
Open) have been designed for in-ear phones from other manu-
facturers. Sounds G and H simulate supraaural headphones.
We recommend that you first find the Sound you like best.
Call up the main menu (unless it is already in the display):
1. Press MENU. The main menu will appear in the display.
Custom Tight
4 A b
█
EAR SND AMB
IVA
Note: If you have set your transmitter to mono mode, you will see
no solid rectangle above the "STEREO" label.
2. Press or to select one of the eight preset Sounds. The
upper display line will indicate the name of the selected Sound,
for instance, this:
Custom Tight
4 A b
█
EAR SND AMB
IVA
or this:
Mold Tight
4 D b
█
EAR SND AMB
IVA
The Sound you selected becomes active immediately so you
can listen to the change on the headphones. It will also be the
basis for all other settings. Once you have left the main menu,
you will not be able to select a different Sound. To do so, you
will need to call up the main menu by pressing MENU or select
the "Sound" menu.
Changing Sounds from the Sound Menu
The Sound menu provides an alternative way to change or select
Sounds. If, for instance, you have called up a stored Setup (refer
to section 7.5.14.), you can only change the Sound setting by
calling up the Sound menu:
1. Press MENU.
2. Press or as many times as necessary to call up this dis-
play:
Menu: Sound
4 A b
█
EAR SND AMB
IVA
O
04
█
STEREO RFCH LOCK
MENU
04
█
STEREO RFCH LOCK
O
MENU
04
█
STEREO RFCH LOCK
O
MENU
04
█
STEREO RFCH LOCK
MENU
O
O
SELECT
O
SELECT
O
SELECT
O
SELECT
19