Connecting To A Stereo Component - Denon DVD-3800 Mode D'emploi

(5) Connecting a basic 5.1-channel surround system
Analog 5.1-channel audio signals can be output from the DVD-3800.
The multichannel audio signals recorded in packed PCM can be played when an AV amplifier equipped with
analog 5.1-channel audio inputs is connected.
DVD-3800
COMPONENT
VIDEO OUT
VIDEO OUT Y S-VIDEO OUT
1 P /C 1
B B
2 P R /C R 2
SL C FL2 FL1 COAXIAL OPTICAL
SR SW FR2 FR1
DIGITAL OUT
AUDIO OUT
(PCM / BIT STREAM)
Front speaker (left)
Surround speaker (left)
AV amplifier with 5.1-channel
NOTES:
• For multi-channel connections, set "AUDIO CHANNEL" under "AUDIO SETUP" at "SETUP" to "MULTI
CHANNEL" and make the "SPEAKER CONFIGURATION", "CHANNEL LEVEL" and "DELAY TIME"
settings.
• Set "LPCM (44.1 kHz/48 kHz)" under "AUDIO SETUP" at "SETUP" to "OFF". (See page 18.)
(If set to "ON", analog audio signals converted to 96 kHz/88.2 kHz will be output when playing sources
recorded at 196 kHz/176.4 kHz.)
• When playing DVDs that are not copyright-protected and the unit is set to output digital and analog audio
signals simultaneously, for some discs only the signals below 96 kHz for the front two channels will be
output for the analog part.
When playing DVDs that are not copyright-protected, set "DIGITAL OUTPUT" at "PURE DIRECT MODE"
to "OFF". (See page 23.)
• When playing DVDs recorded in MPEG audio format, the audio signals are down-mixed to 2 channels for
output.
• With the DVD-3800, we recommend turning the digital output off and only outputting analog signals in
order to keep interference from the digital output circuitry to the minimum and allow you to enjoy high bit,
high sampling frequency, high quality multi-channel sound.
To power outlet
AV1
REMOTE CONTROL
RS-232C ROOM TO ROOM
IN OUT
AV2
Center speaker
Front speaker (right)
Subwoofer
SURROUND MODE MULTI FUNCTION Surround speaker (right)
DIRECT STEREO SURROUND DOLBY SURROUND DTS SCREEN WIDE 5CH / 7CH STEREO SIMULATION DSP STATUS SELECT MODE FUNCTION CONTROL
PHONES
MODE INPUT ANALOG EXT. IN CINEMA / MUSIC SURROUND 6.1 / 7.1 ON / OFF VIDEO TONE DEFEAT M-ZONE 1 REC / M-ZONE 2
INPUT REC SELECT / M-ZONE
input terminals
(6) Connecting to a Digital Recorder (MD Recorder, DAT Deck, etc.)
Set the "AUDIO SETUP" default setting as shown below. (See page 18.)
• "DIGITAL OUT" → "PCM"
"LPCM (44.1 kHz / 48 kHz)" → "ON"
Playing DVDs with incorrect settings may result noise that could damage your ears or the speakers.
DVD-3800
COMPONENT
VIDEO OUT
AC IN
VIDEO OUT Y S-VIDEO OUT
1 P /C 1
B B
2 P /C 2
R R
SL C FL2 FL1 COAXIAL OPTICAL
SR SW FR2 FR1
DIGITAL OUT
AUDIO OUT
(PCM / BIT STREAM)
75 Ω /ohms pin-plug cable (commercially available)

(7) Connecting to a Stereo Component

DVD-3800
COMPONENT
VIDEO OUT
VIDEO OUT Y S-VIDEO OUT
1 P B /C B 1
2 P /C 2
R R
SL C FL2 FL1 COAXIAL OPTICAL
SR SW FR2 FR1
DIGITAL OUT
AUDIO OUT
(PCM / BIT STREAM)
NOTES:
• When connecting to a 2-channel audio stereo device, set "AUDIO CHANNEL" under "AUDIO SETUP" at
"SETUP" to "2 CHANNEL" (see page 17). For multi-channel sources, the signals are down-mixed into two
channels (analog). (Only the front left and right channels are output for sources for which down-mixing is
prohibited.)
• Set "LPCM (44.1 kHz/48 kHz)" under "AUDIO SETUP" at "SETUP" to "OFF". (See page 18.)
(If set to "ON", analog audio signals converted to 48 kHz will be output for linear PCM or packed PCM
sources.)
• Set "DIGITAL OUTPUT" at "PURE DIRECT MODE" to "OFF". (See page 23.)
(If set to "ON", analog audio signals converted to 96 kHz/88.2 kHz will be output when playing sources
recorded at 196 kHz/176.4 kHz.)
AV1
REMOTE CONTROL
RS-232C ROOM TO ROOM
IN OUT
AV2
Digital audio input
connector (OPTICAL)
Optical fiber cable (commercially available)
Stereo component
AV1
AV2
ENGLISH
B
8 9
Digital audio
input
connector
(COAXIAL)
9