Features; Description; Installing The Gsm Interface - Bentel Profiline AZ6400 Instructions D'installation

FEATURES

ˆ Simulates PSTN line
ˆ Switches to GSM Network in the event of PSTN
Trouble (Line down)
ˆ Manages and signals Incoming/Outgoing calls
ˆ 7 segment status display
ˆ GSM signal strength indicator
ˆ 5 programmable OC Outputs
ˆ Houses 12V-1.2Ah battery (not supplied)
ˆ Protected against tamper
ˆ Protected against PSTN over-voltage
ˆ Dual Band
ˆ 4 Alarm Channels
ˆ Manages 8 SMS Text Communications
ˆ Manages 8 (20 digit) telephone numbers per
channel
ˆ Control Outputs via SMS
ˆ Stop Alarm Jumper and SERVICE Channel
ˆ Records up to 8 messages: 4 x 15 seconds
and 4 x 7 seconds
ˆ Voice Message can be assigned to each Alarm
Channel
ˆ Voice Message Priority (Channel 1)
ˆ 4 independent Alarm channels with priority
management (Channel 1 priority)
ˆ Up to 4 call cycles
ˆ Stop Alarm Jumper (SERV)
ˆ Digital message Recording/Playback
ˆ Message playback
ˆ Plays Alarm message up to 4 times
ˆ Programmable Handshake
G G G G G

DESCRIPTION

The engineer-friendly
interface provides total confidence in all security
and surveillance applications. It can be simply and
cost-effectively intergrated with all alarm systems,
and can substitute the PSTN line completely, in
zones where the GSM Service is provided, and
where hardwired telephone devices cannot be
installed (mountain cabins, beach bungalows, etc.).
24
7DEOH   7(&+1,&$/ 63(&,),&$7,216
3RZHU 6XSSO\ 9ROWDJH
2SHUDWLQJ 7HPSHUDWXUH
'LPHQVLRQV : [ + [ '  [  [  PP
:HLJKW ZLWKRXW EDWWHU\
The
Central station communications, and all the tele-
phone-control functions normally provided by te-
lephone diallers such as the B-TEL99.
The performance of this device greatly depends
on the selected GSM Network, and signal stren-
gth.
The
signal strength,
which transmit properly over the GSM Networks.
The GSM signal strength is of utmost importance,
the GSM Interface should not be located in places
where the GSM signal is weak (e.g. only one si-
gnal strength LED ON), as communications will be
at risk.
The
Texts, and provides a remote control feature that
will allow Users to turn ON the 5 Outputs over the
phone.
Due to the characteristics of GSM Networks, the
or data transmission, or for Teleservice operations.
The
tected metal casing, with built-in status display.

INSTALLING THE GSM INTERFACE

The
place, away from radio transmitters and similar de-
vices. When choosing the placement, remember that
the
power supply (usually from the Security system).
Both models must be Earthed, and equipped with
standby batteries (see Figure 4).
G G G G G
analogue
. Remove the screws and the metal casing [ ].
. Drill the anchor screw holes (use the back-
plate to mark the screw locations).
G
. Lay the cables, then pull them through the ca-
0D[ &XUUHQW GUDZ
manages two-way voice and
supports
protocols and, in areas with optimum
and
can manage up to 8 SMS
cannot be used as a modem for fax
is housed in a tamper-pro-
should be located in a safe dry
requires a 13.8 V
 9
 P$
 · ƒ&
 J
,
, all of
/1 A min.
_