Notice/Caution On Using Bluetooth Device (Only For Kw-V50Bt Region 1/Kw-V30Bt Region 1); Speci Cations - JVC KW-V50BT Mode D'emploi

REFERENCES
❏ Bluetooth
Phone sound quality is poor.
• Reduce the distance between the unit and the
Bluetooth mobile phone.
• Move the car to a place where you can get a better
signal reception.
T h e o s u n d i i s t n r e u r p e t d r o k s p i
Bluetooth audio player.
• Reduce the distance between the unit and the
Bluetooth audio player.
• Disconnect the device connected for Bluetooth
phone.
• Turn o , then turn on the unit.
• (When the sound is not yet restored) connect the
player again.
The connected audio player cannot be
controlled.
• Check whether the connected audio player
supports AVRCP (Audio Video Remote Control
Pro le).
Bluetooth device does not detect the unit.
• Search from the Bluetooth device again.
The unit does not make pairing with the
Bluetooth device.
• For devices compatible with Bluetooth 2.1:
• For devices compatible with Bluetooth 2.0:
Enter the same PIN code for both the unit and
target device. If the PIN code of the device is not
indicated on its instructions, try "0000" or "1234."
E h c o r o n i o e s o c c r u . s
• Adjust the microphone unit position.
• Adjust the echo volume or noise reduction
66
The unit does not respond when you try to copy
the phone book to the unit.
• You may have tried to copy the same entries (as
stored) to the unit.
Notice/Caution on using Bluetooth
device
p e d w i h e l s u n i g a
KW-V30BT Region 1)
IC (Industry Canada) Notice
This device complies with Industry Canada licence-
exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2)
this device must accept any interference, including
interference that may cause undesired operation of
the device.
The term "IC: " before the certi cation/ registration
number only signi es that the Industry Canada
technical speci cation were met.
CAUTION
This equipment complies with FCC/IC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency
(RF) Exposure Guidelines in Supplement C to OET65
and RSS-102 of the IC radio frequency (RF) Exposure
rules. This equipment has very low levels of RF
energy that it deemed to comply without maximum
permissive exposure evaluation (MPE). But it is
desirable that it should be installed and operated
keeping the radiator at least 20 cm or more away
from person's body (excluding extremities: hands,
wrists, feet and ankles).
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential
(Only for KW-V50BT Region 1/
radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication.
• Contains Transmitter Module
FCC ID : YZP-RBFAC21XX
• Contains Transmitter Module
IC: 7414A-RBFAC21XX

Speci cations

❏ Monitor section
Picture Size (W x H)
KW-V50BT: 6.95 inches (diagonal) wide
156.6 mm x 81.6 mm (6-3/16" x
3-3/16")
KW-V30BT: 6.1 inches (diagonal) wide
136.2 mm x 72 mm (5-6/16" x
2-13/16")
Display System Transparent TN LCD panel
Drive System TFT active matrix system
Number of Pixels 1 152 000 (800H × 480V × RGB)
E ective Pixels 99.99%
Pixel Arrangement
RGB striped arrangement
Back Lighting LED