Settings Mode - Hedson IRT 3-1 PcD Mode D'emploi

8.

Settings Mode

8.1 Log In
To enter the settings mode you first have to "log in". Press
both arrow keys as you turn the main switch on. The
display will ask you for a PIN code.
8.2 PIN code
Use the arrow keys to fill in the correct digit. Press enter
to confirm and edit the second, third, and fourth digit of
the code.
No code is required for basic settings, just press OK
for the default code of 0000. To change this code, read
chapter 8.4.5 "Basic PIN Code".
Advanced PIN code
Used for program adjustments and advanced settings.
To change this code, read chapter 8.4.13 "Advanced Pin
Code".
Attention! An entered PIN code is valid globally in the
software until the main switch is turned off, i.e. if you
enter advanced settings mode and then exit to program
mode. The program editing will still be editable until the
main power is turned off.
8.3 Navigation
To adjust a setting, press edit. To go back from edit mode
to settings mode without saving, press cancel.
Note! If you press exit from settings mode you will be
redirected to "program mode". You will then need to re-
peat from step 8.1 "Log In" to enter 8.4 "Settings" again.
Edit
mode
Use arrow keys to change
language and select to
confirm.
6 6
5780
Press exit
and you will
be directed
to "program
mode".
Use the arrow keys
to scroll through the
settings, see table in
chapter 8.4.
8.4 Settings
Ch. Overview
8.4.1 1 Select Language
8.4.2 3 Process Alarm
8.4.3 4 Temp Unit
8.4.4 5 Buzzer
8.4.5 7 Basic PIN Code
8.4.6 8 Short Dist lim.
8.4.7 9 Long Dist lim.
8.4.8 15 Temperature Ctrl
8.4.9 16 Disp. Contrast
8.4.10 18 Distance
8.4.11 23 Filter Time
8.4.12 25 Contin. Mode
8.4.13 36 Advanced PIN Code
8.4.14 37 Dist Unit
8.4.15 43 Advanced Code
8.4.16 44 Reset Prog. Settings
8.4.17 45 Reset Filter Timer
8.4.18 46 Statistics
8.4.19 47 Perform Self test
8.4.20 48 Program Time Scale
8.4.21 49 Proc. Alarm Temp.
8.4.1 1 Select Language
Use the up and down arrow keys to scroll through the
fourteen different languages (arranged alphabetically) un-
til the correct language appears. Press select to confirm.
If you accidently switch to a language that you do not
understand, turn the main switch on while pressing the
"cassette in use" button. The dryer will then start up with
British English.
8.4.2 3 Process Alarm
Not applicable for this model.
8.4.3 4 Temp. Unit
Not applicable for this model.
8.4.4 5 Buzzer
The sound effects can be muted/activated by using the
arrow keys to select no/yes. Press select to confirm.
8.4.5 7 Basic PIN Code
You can change the PIN code to prevent unauthorized
access to the basic setting as described in table in
chapter 8.4. To do this use the up and down arrow keys
to change the first digit, press select to confirm. Continue
with the second, third and fourth digit. When completed
press select to confirm the new four digit PIN code.
8.4.6 8 Short Distance Limit
The original settings for the correct short distance limit
is 55 cm. You can change the value for the short distance
limit from 35 to 95 cm. Settings higher than 80 cm are
not recommended. Press select to confirm.
EN
available in
Basic Advanced
x
x
x
x x
x
x
x
x
x x
x
x
x
x
x
x
x
x
x x
x x
x
x
713686 rev 8