Publicité
Les langues disponibles
Les langues disponibles
Installer Settings
Installer Checkout
Basic Settings
Settings
80
68
80
80
Backlight Enabled?
Yes
Zoning System Test
Linearize Dampers
Resume Schedule
Group 1
Away
71
75
71
72
36
Outside Temp Selection?
T957_O Low Refrigerant Pressure
Internet
Basic
Time
Away
Home
status: Setting airflow
Away
Vacation
Refrigeration
Cooling to
34
85
70
65
OFF
BACK
BACK
BACK
Furnace Settings
Installer Checkout
Installer Settings
Basic Settings
80
80
80
68
Backlight Enabled?
Yes
Zoning System Test
Linearize Dampers
Resume Schedule
Group 1
Away
71
72
75
71
36
Furnace
AC/HP
Thermostat
Outside Temp Selection?
T957_O Low Refrigerant Pressure
Internet
Air Handler
Defaults
Home
Away
status: Setting airflow
Warning! These settings are to be used
Refrigeration
Cooling to
by a qualified HVAC contractor ONLY
70
65
85
34
OFF
BACK
BACK
BACK
Furnace Settings
68
LED Display Orientation
Upflow
Away
Furnace Blower Off Delay
90 secs.
71
Hi Heat Airflow Adjust
None
Lo Heat Airflow Adjust
None
G Input Fan Control
Off
Aux #1 Config
N.O.
Off
Aux #2 Config
N.O.
Off
OFF
BACK
> Return to Table of Contents
To enter the Installer Settings menu, select Menu > Settings, then tap and hold
Zone 3
Zone 4
!
on "Installer" on the bottom right of the screen for five seconds.
21
Humidity
47%
44%
61%
44%
CFM: 840
Fan
54
Dining Room
Installer
Basement
UNITS
Furnace Status (Menu > Settings > Installer > Furnace)
Zone 3
Zone 4
!
Go to Menu > Settings > Installer (tap and hold) > Furnace.
21
47%
61%
44%
44%
CFM: 840
54
Dining Room
Basement
UNITS
LED Display Orientation – Flips the furnace's LED diagnostic display so it is
Zone 3
readable in the upflow or downflow position.
Furnace Blower Off Delay – 90 (default), 120, 150, 180 seconds. Amount of
47%
time the blower will run after a furnace heating call has ended.
Hi Heat Airflow Adjust – This setting will adjust the heat gain of the second
Dining Room
MORE
stage or high stage of the two-stage furnace. There are five optional settings to
choose from. The default is 'None'.
• Higher Airflow: Will decrease the second stage Midpoint heat rise -7˚F by
increasing the CFM
• None: Nominal CFM and heat rise across the furnace
• Lower Airflow: Will increase the second stage Midpoint heat rise +7˚ by
lowering the CFM.
• Lowest Airflow: Will increase the second stage Midpoint heat rise +12˚ by
lowering the CFM even lower
Lo Heat Airflow Adjust – This setting will adjust the heat gain of the first stage
or the low stage of the two-stage furnace. There are five optional settings to
choose from. The default is 'None'.
• Higher Airflow: Will decrease the first stage Midpoint heat rise by -7˚F by
increasing the CFM
• None: Nominal CFM and mid heat rise across the furnace
• Low Airflow: Will increase the first stage Midpoint heat rise +7˚ by lowering
the CFM
• Lowest Airflow: Will increase the first stage Midpoint heat rise +12˚ by
lowering the CFM
G Input Fan Control – Off (default), Low, Medium Lo, Medium, Medium
High, High: airflow to run if the G terminal is activated. To be used for add-on
accessories (like ventilators) that are wired to the furnace G terminal and wish
to run the blower.
EcoNet
Smart Thermostat User Guide
®
28
Publicité
Chapitres
