How To Test A Humidifier - EcoNet RETST700SYS Guide D'utilisation

Settings (con't)
Installer Checkout Humidification Basic Settings
80 68 80 80
Enable Humidification? Backlight Enabled? Yes
No
Zoning System Test Linearize Dampers
Resume Schedule Group 1 Away
71 72 75 71 36
Outside Temp Selection? Humidify Set Point T957_O Low Refrigerant Pressure
Internet 30 %
Humidify During...
Heat
Smart Control
Off
Home Away
status: Setting airflow
Humidity With Fan Off
Refrigeration
Cooling to
65 34 70 85
OFF
BACK BACK BACK
Installer Checkout Humidification Basic Settings
80 80 80 68
Backlight Enabled? Enable Humidification?
Yes No
Zoning System Test Linearize Dampers
Resume Schedule Group 1 Away
71 72 71 75 36
Humidify Set Point Outside Temp Selection? T957_O Low Refrigerant Pressure
30 % Internet
Humidify During...
Heat
Smart Control
Off
Home Away
status: Setting airflow
Humidity With Fan
Off
Refrigeration Cooling to
70 65 85 34
OFF
BACK BACK BACK

How to Test a Humidifier

Adjust the humidify set point up to 'TEST', select Humidify during "Heat/Fan", then turn on a continuous fan
speed on the Fan screen under Settings. This should force the humidifier to run. This setting will last for 30
minutes, where the maximum setting will return to 4% below the dehumidification set point.
Installer Checkout Basic Settings Settings
80 80 80 68
Backlight Enabled?
Yes
Zoning System Test Linearize Dampers
Resume Schedule Group 1 Away
71 72 71 75 36
Outside Temp Selection?
T957_O Low Refrigerant Pressure Internet
Basic Time
Home Away
status: Setting airflow
Away Vacation
Refrigeration
Cooling to
65 85 34 70
OFF
BACK BACK BACK
> Return to Table of Contents
Humidification (Menu > Settings > Humidity > Humidification)
Zone 3
Zone 4
!
Enable Humidification – The system can control a humidifier attached to the
21
furnace or air handler to increase humidity in the space. It is important to note
61% 47% 44% 44%
you cannot humidify above the dehumidification set point.
CFM: 840
54
Humidification Set Point – This setting allows you to choose the indoor
Dining Room
Basement UNITS
relative humidity desired, under which humidification will activate. The default
is humidification set point is 30% and is configurable between 15 and 45%.
Humidify During – Select the modes in which humidification will be
performed. Humidification can occur during heating, continuous fan and/or
cooling mode.
• Heat – Humidifier will operate with equipment during Heat if a humidification
demand is present.
• Heat/Fan – Humidifier will operate with equipment during these modes if a
humidification demand is present.
• Heat/Fan/Cool – Humidifier will operate with equipment during these modes
if a humidification demand is present.
Smart Control – Smart Control is used to reduce or prevent water
Zone 3
Zone 4
!
condensation on the inside of windows while humidifying in the winter season.
21
The control monitors indoor and outdoor temperatures and reduces the
humidification percentage according to the Smart Control level chosen by the
44% 44% 61% 47%
CFM: 840
user. Start out with the Low setting. If objectionable condensation occurs on
54
windows, choose the Medium or High setting.
Dining Room
Basement UNITS
Humidify With Fan – If there is a call to humidify and the fan and heating/
cooling are off, the fan will be forced on to humidify. Select the desired fan
speed from Low to High.
Note: Humidification is only available if a humidifier is installed.
Away Settings (Menu > Settings > Away)
Zone 3
Zone 4
!
Your system will follow the customized heating, cooling and fan settings when
21
Humidity
you place your system into 'Away' mode. The system can be placed into
44% 47% 44% 61%
Away by selecting the Home icon (closed door) on the home screen. Once
CFM: 840
Fan
54 the system is placed into Away mode it will remain until canceled. Simply tap
Dining Room Installer
Basement UNITS the Away icon (open door) to exit Away mode. The system will resume the
schedule or return to the previous settings if a schedule is not being followed.
You can also exit Away by increasing or decreasing the temperature.
Note: If your system is in Cool or Heat when placed into Away mode your system will only manage
to the respective Away set point.
EcoNet Smart Thermostat User Guide
®
15