Air Handler Settings; Caring For Your Thermostat - EcoNet RETST700SYS Guide D'utilisation

Air Handler Settings

Installer Checkout Installer Settings Basic Settings
80 68 80 80
Backlight Enabled?
Yes
Zoning System Test Linearize Dampers
Resume Schedule Group 1 Away
75 71 71 72 36
Furnace AC/HP Thermostat
Outside Temp Selection? T957_O Low Refrigerant Pressure
Internet
Air Handler Defaults
Home Away
status: Setting airflow
Warning! These settings are to be used
Refrigeration Cooling to
by a qualified HVAC contractor ONLY
65 85 34 70
OFF
BACK BACK BACK
Air Hander Settings Installer Checkout Basic Settings
80 68 80 80
Electric Heater Size None
Backlight Enabled? Yes
Zoning System Test Linearize Dampers
Resume Schedule Group 1 Away
71 75 71 72 36
Outside Temp Selection? T957_O Low Refrigerant Pressure
Internet
EXV Superheat Offset 0° F
O Input Fan Control Off
Home Away
Aux #1 Config N.O. Off
status: Setting airflow
Aux #2 Config N.O. Off
Refrigeration
Cooling to
Filter Type Media
34 85 65 70
OFF
BACK BACK BACK

Caring for your Thermostat

Cleaning
You can clean your thermostat screen by lightly spraying water on the provided lens cloth or a clean microfiber
cloth. Wipe the surface of the screen with the dampened cloth. It is recommended you first lock the screen
(Menu > Settings > Basic > Screen Lock set to 'Yes')
Note: Never spray any liquids directly onto your EcoNet Smart Thermostat.
Rebooting
You can reboot your EcoNet Smart Thermostat by cycling power to the thermostat. Rebooting will not alter
programming, settings or configuration options.
Note: When significant changes are made to the EcoNet system a complete power cycle is required. Control board replacements, upgrading
from a non-communicating outdoor unit to a communicating outdoor unit and the addition of zoning require the thermostat be reset to
factory defaults, followed by a power cycle to all equipment.
Resetting the Thermostat
Installer Checkout Installer Settings Basic Settings
80 68 80 80
Backlight Enabled?
Yes
Zoning System Test Linearize Dampers
Resume Schedule Group 1 Away
75 72 71 71 36
Furnace AC/HP Thermostat
Outside Temp Selection? T957_O Low Refrigerant Pressure
Internet
Air Handler Defaults
Home Away
status: Setting airflow
Warning! These settings are to be used
Refrigeration Cooling to
by a qualified HVAC contractor ONLY
70 65 85 34
OFF
BACK BACK BACK
> Return to Table of Contents
Air Handler Status (Menu > Settings > Installer > Air Handler)
Zone 3
Zone 4
!
Go to Menu > Settings > Installer (tap and hold) > Air Handler.
21
44% 44% 47% 61%
CFM: 840
54
Dining Room
Basement UNITS
Electric Heater Size – If electric strip heaters are installed in the air handler
Zone 3
Zone 4
!
you will need to select the appropriate size.
21
Electric Heat Airflow Select – Four choices available. Refer to air handler
44% 47% 61% 44%
installation instructions for air flow settings.
CFM: 840
54
Dining Room See pages 28-29 for the G Input and AUX Input details. These settings are the
Basement UNITS
same for both furnace and air handler.
Default Status (Menu > Settings > Installer > Default)
Zone 3
Zone 4
!
At some point during the life of your EcoNet Smart Thermostat you may want
21
to quickly restore it to the default state. First, enter the Installer Settings menu
61% 44% 44% 47%
by selecting Menu > Settings, then tap and hold on "Installer" on the bottom
CFM: 840
54
right of the screen for five seconds. Once in the Installer menu, tap Defaults,
Dining Room
Basement UNITS
view the warning and tap Enter to restore all settings to factory default.
Note: This will reset all settings including a programmed schedule, date and time to
factory default settings.
EcoNet Smart Thermostat User Guide
®
32