Scheppach HL750ST Traduction Des Instructions D'origine page 22

Remaining hazards
The machine has been built using modern tech-
nology in accordance with recognized safety
rules. Some remaining hazards, however, may
still exist.
• The splitting tool can cause injuries to fingers and
hands if the wood is incorrectly guided or support-
ed.
• Thrown pieces can lead to injury if the work piece
is not correctly placed or held.
• Injury through electric current if incorrect electric
connection leads are used.
• Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
• Remaining hazards can be minimized by following
the safety instructions as well as the instructions in
the chapter Authorized use and in the entire oper-
ating manual.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Release the handle button and switch off the ma-
chine prior to any operations.
• Avoid accidental starts of the machine: Do not
press the start button while inserting the plug into
the socket.
• Use the tools recommended in this manual to ob-
tain the best results from your machine.
• Always keep hands away from the work area when
the machine is running.
7. Technical data
Dimensions L x W x H
(with base frame)
Wood ø min. - max.
Wood length min.- max.
Weight approx.
Motor
Input power
Rating
Splitting Power
Cylinder rise
Cylinder speed (fast fwd.)
Cylinder speed (return)
Hydraulic fluid capacity
Operating pressure
Motor speed
Subject to technical changes!
Noise
m Warning: Noise can have serious effects on your
health. If the machine noise exceeds 85 dB (A),
please wear suitable hearing protection.
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
All manuals and user guides at all-guides.com
1100 x 720 x 1350
mm
50 - 250 mm
150 - 520 mm
55 kg
230 V~ / 50 Hz
2300 W
S3 50%
max. 7 t
400 mm
37 mm/sec
70 mm/sec
4,2 l
240 bar
2800 1/min
Characteristic noise emission values
sound power level L 83,8 dB (A)
WA
sound pressure level L 70,3 dB (A)
pA
uncertainly K 1,5 dB
WA/pA
*S3, periodic intermittent operation without influence
of the starting process on the motor heating. Identical
duty cycles with a period at load followed by a peri-
od at no load. Running time 10 minutes; duty cycle is
50% of the running time.
Pressure:
The performance level of the built-in hydraulic pump
can reach a short-term pressure level for a splitting
force of up to 7 tons. In the basic setting, hydraulic
splitters are set at the factory to an approx. 10% low-
er output level. For safety reasons, the basic settings
must not be changed by the user. Please note that
external circumstances such as operating and ambi-
ent temperature, air pressure and moisture affect the
viscosity of the hydraulic oil. In addition, manufactur-
ing tolerances and maintenance errors can affect the
reachable pressure level.
8. Unpacking
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• In case of complaints the dealer must be informed
immediately. Subsequent complaints will not be ac-
cepted.
• If possible, store the packaging until the warranty
period has expired.
• Read the operating manual to make yourself famil-
iar with the device prior to using it.
• Only use original parts for accessories as well as
for wearing and spare parts. Spare parts are avail-
able from your specialized dealer.
• Specify our part numbers as well as the type and
year of construction of the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!