Publicité
Les langues disponibles
Les langues disponibles
Headrest Adjustment
The Axkid MINIKID 4 MAX is equipped with an adjustable headrest (A).
Always ensure that the headrest is positioned in the correct height for your child when using your
Axkid MINIKID 4 MAX. Check that the shoulder straps (B) are going through the seat straight from your child' s
shoulders or maximum 1 cm above. If not, adjust the headrest (A) accordingly.
Note: The harness tension needs to be released if the headrest cannot be pulled up to a suitable height. Press the belt
harness release button (F) to loosen the harness.
Removing Axkid MINIKID 4 MAX car
seat from the vehicle
•
Unzip the zipper and open the belt clamp lid (O). Unlock the vehicle seat belt by pressing the red button on the
seat belt buckle. Open the belt clamp (N) and pull the vehicle seat belt and guide it through the seat belt slots (D)
to remove it from the car seat.
•
Unlock the lower tethers (M) by holding on to the connectors with your hand and pressing on the grey button
with your thumb. While keeping the connector in your hand, slowly feed it back to the car seat. Be careful not to
let go of the lower tether connector, as it will retract back automatically with high speed.
•
Push the support leg button (Q) and collapse the support leg (P) to its shortest position.
•
Press the recline adjustment lever (G) and push in the recline angle adjuster (T) to its shortest position. Lift the
Axkid MINIKID 4 MAX out of the vehicle.
Tip: Lock the harness buckle and tension the harness before removing the car seat from the vehicle. You can then use the
shoulder straps (R) as a carrying handle, making it easier to lift out the car seat and transporting it outside of the vehicle.
Important: Never carry the car seat by holding in the headrest (A).
Recycling your car seat
Axkid strongly recommends recycling of old car seats. Before leaving the seat at your local recycling
station cut off the harness straps from the seat, remove the textile cover, remove as many Styrofoam
parts as possible, separate metal and plastic parts if possible. The main part of the seat should be
marked unsafe or expired (use a marker) to deter anyone from using it again. Please check your local
municipal guidelines for recycling instructions for the different materials.
20
Care and maintenance
The seat textile cover can be machine washed at 30º C on a gentle cycle. Do not put the cover in a dryer as this can
damage the cover and the padding may separate from the fabric. Visit www.axkid.com to find videos explaining how
to remove and attach the cover. If the textile seat cover needs replacing, ensure only original products from Axkid are
used. If other products are used, Axkid MINIKID 4 MAX car seat' s safety system may be compromised and could lead
to severe injury in case of an accident.
Any plastic parts of Axkid MINIKID 4 MAX car seat can be cleaned with mild detergent and water. Do not use
aggressive chemicals containing solvents or similar, as this can cause damage to the plastic and compromise the
safety of the car seat.
Remove the textile cover:
•
Remove the ASIP pad (I) if attached.
•
Pull the headrest (A) to its topmost position.
•
Loosen the harness by pressing the harness release button (E) and pull out both shoulder straps (R) at the same time.
•
Unzip the two zippers on the underside of the headrest (A) and carefully pull the cover off from the headrest (A).
•
Lower the headrest (A) to the lowest position.
•
Unlock the harness buckle by pressing the buckle release button (C) and remove the buckle cover.
•
Unzip the zipper and open the belt clamp lid (O) and remove the plastic lid from the textile cover.
•
Unzip the zipper underneath the car seat and open the 4 buttons on the textile cover on the backside of the car seat.
•
Unzip the two zippers at the backrest on the inside of the car seat and gently remove the textile cover from the car seat.
Be careful around the ASIP pad and other plastic covers to avoid damaging the textile. Don't pull to hard.
•
Open the shoulder pads and gently remove them from the shoulder straps (R).
Install the textile cover:
•
Reverse the steps from the instruction above to install the textile cover on the car seat again.
Note: The shoulder pads can be installed at different positions. Install them in a position suitable for your child, the
shoulder pads should be positioned on top of the shoulder and on the chest of your child. Also make sure that the
rubber side of the shoulder pad is facing your child' s chest.
Warranty
Axkid MINIKID 4 MAX car seat is covered by a 24-month warranty from date of purchase. Ensure you save your
receipt and bring it to your place of purchase if you have any warranty issues.
Handle the seat with care. Never carry the seat by holding in the headrest (A).
The warranty does not cover:
•
Normal wear and tear.
•
Damage due to incorrect use, neglect, or accident.
•
If repairs have been carried out by a third party.
•
All materials used have a very high UV-resistance rating. However, UV-light is very aggressive and will ultimately
lead to fading of the seat cover. This is not covered by our warranty as it is considered normal wear and tear.
21
EN
Publicité
