Installation; Installation Room; Ambient Temperature; Ventilation - Bosch B36ET Série Guide D'utilisation Et D'entretien

Installation

m
WARNING
Do not install the appliance:
– outdoors,
– in an environment with dripping
water,
– in rooms which are at risk of frost.
The appliance is very heavy – for
empty weight see following table:
36"
Bottom freezer (3-door)
approx. 430 Ibs/195 kg

Installation room

Install the appliance in a dry, well
ventilated room.
The installation location should neither
be exposed to direct sunlight nor near a
heat source, e.g. a cooker, radiator, etc.
If installation next to a heat source is
unavoidable, use a suitable insulating
plate or observe the following
minimum distances to a heat source:
1
– 1 / " (3 cm) to electric or gas
4
cookers.
– from an oil or solid-fuel cooker
13
11 / " (30 cm).
16

Ambient temperature

The climatic class can be found on the
rating plate. It states the room
temperature within which the appliance
can be operated.
Climatic Permitted ambient
class temperature
SN +50 °F to 89.6 °F
(+10 °C to 32 °C)
N +60.8 °F to 89.6 °F
(+16 °C to 32 °C)
ST +60.8 °F to 100.4 °F
(+16 °C to 38 °C)
T +60.8 °F to 109.4 °F
(+16 °C to 43 °C)

Ventilation

Never cover the ventilation openings in
the base panel. The cooling motor
otherwise has to increase ist output, and
m
this increases the electricity
consumption.

Installation cavity

It is important to observe the specified
dimensions of the installation cavity for a
trouble-free installation of the appliance
and for the subsequent general view of
the furniture front.
In particular ensure that the cavity is
square. Squareness can be checked by
suitable means, e.g. spirit level, diagonal
measurements, etc.

Furniture/Fixtures

The new appliance will be mounted
securely to adjacent and overhead
furniture/fixtures.
For this reason it is essential that all
attachable furniture/fixtures are
connected securely to the base or the
wall by suitable means.

Base

To ensure that the appliance is installed
securely and functions properly,
the base must be flat and level.
The base must be made of a hard, rigid
material.
The installation area must be the same
height as the rest of the room.
On account of the heavy weight of a fully
loaded appliance, a load-bearing base is
required.
The fully-loaded weight for this appliance
is approx. 1110 Ibs/500 kg.
If in doubt, contact an architect or
a building expert.
Installing and
connecting the
appliance
CAUTION
Have the appliance installed by an
electrician according to the enclosed
installation instructions.
After installing the appliance, wait at least
8 hours before switching on the
appliance. During transit the oil in the
refrigeration system may have moved.
Before switching on the appliance for the
first time, clean the inside of the
appliance.
Always connect the water before the
power.
Apart from statutory national regulations,
you should adhere to the connection
terms applied by local electricity and
water companies.
Do not remove the transportation
protection devices from the shelves and
storage compartments until the
appliance has been installed.
Connecting the
water
A cold water connection is required for
operation of the automatic ice maker.
The water pressure must be between
25 and 120 p.s.i. (1.72–8.25 bar).
The installation must comply with local
plumbing regulations and local and state
laws.
A separate shut-off valve must be
installed for the appliance water
connection.
The shut-off valve for the water
connection must not be behind the
appliance. It is recommended to place
the shut-off valve directly next to the
appliance (base unit) or in another easily
accessible location.
7