Table des Matières
Publicité
OBJ_BUCH-2279-002.book Page 12 Wednesday, May 6, 2015 2:21 PM
12 | English
Safety Warnings for Screwdriver
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may con-
tact hidden wiring. Fasteners contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
Hold the machine with a firm grip. High reaction torque
can briefly occur while driving in and loosening screws.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
In case of damage and improper use of the battery, va-
pours may be emitted. Ventilate the area and seek
medical help in case of complaints. The vapours can irri-
tate the respiratory system.
Use the battery only in conjunction with your Bosch
power tool. This measure alone protects the battery
against dangerous overload.
The battery can be damaged by pointed objects such as
nails or screwdrivers or by force applied externally. An
internal short circuit can occur and the battery can burn,
smoke, explode or overheat.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for driving in and loosening screws
and bolts as well as for tightening and loosening nuts within
the respective range of dimension.
The light of this power tool is intended to illuminate the power
tool's direct area of working operation and is not suitable for
household room illumination.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Tool holder
2 Carrying strap
3 Belt clip*
4 Battery pack*
5 Battery unlocking button*
1 609 92A 1CL | (6.5.15)
6 Rotational direction switch
7 On/Off switch
8 "PowerLight"
9 Handle (insulated gripping surface)
10 Application tool (e. g. an impact socket)
*Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cordless Impact Screwdriver
Article number
Rated voltage
No-load speed
Impact rate
Maximum torque, hard
screwdriving application
according to ISO 5393
Bolt size
Tool holder
Weight according to
EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
*
– during operation
and during
storage
Recommended batteries
Recommended chargers
* Limited performance at temperatures <0 °C
**
only for wireless charging batteries
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-2.
Typically the A-weighted noise levels of the product are:
Sound pressure level 100 dB(A); Sound power level
111 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-2:
Impact tightening of fasteners of the maximum capacity of the
2
2
tool: a
=18 m/s
, K=1,5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
GDS 18 V-EC 250
3 601 JD8 1..
V=
18
-1
min
0 –2 400
-1
min
0 –3 400
Nm
250
mm
M10 – M18
½"
kg
2.0
°C
0... +45
°C
-20... +50
GBA 18V..
GBA 18V...W
AL 18..
GAL 3680
GAL 18...W**
Bosch Power Tools
Publicité
Table des Matières
